Page 74 - M1-12 Ops Manual McMurdo 2016

SEr3 = Baud rate for serial link
R
S
Pt 100 Pt 100 T
T
range range range range range range
0/
+3200 °F +3200 °F +400.0 °F +1470 °F +400.0 °C +750 °F
Not available when SEr1 = OFF
From 600 to 19200 baud.
NOTE: 19200 baud is shown on display as 19.20.
0/ -199.9 / -330 / -199.9 / -330 /
SEr4 = Byte format for serial link
9, 25 or 27, the
Not available when SEr1 = OFF
7E = 7 bits + even parity (For ERO protocol only) 7O = 7 bits + odd parity (For ERO protocol only) 8E = 8 bits + even parity
8O = 8 bits + odd parity
8 = 8 bits no parity
If a different selection is desired, P36 may be modified.
P1 - Input type and standard range
This parameter is available only when a linear input is selected (P1 = 11, 12, 13, 14, 15, 16, 17 or 18).
0 = TC type
1 = TC type
2 = TC type
3 = TC type
4 = TC type
5 = TC type
6 = TC type
7 = TC type
8 = TC type
9 = RTD type
10 = RTD type
11 = mV
L
L
J
J
K
K
N
R
S
Pt 100 Pt 100 Linear Linear Linear Linear Linear Linear Linear Linear L
range range range range range range range range range range range range range range range range range range range range range
0 /
+400.0°C +900 °C +400.0 °C +1000 °C +400.0 °C +1370 °C +1400 °C +1760 °C +1760 °C +400.0 °C +800 °C 60 mV 60 mV 20 mA 20 mA 5V 5V 10V 10V +1650 °F +1830 °F +2500 °F +2550 °F
----. = No decimal figure. ---.- = One decimal figure. --.-- = Two decimal figures. -.--- = Three decimal figures.
12 = mV
13 = mA
14 = mA
15 =V
16 =V
17 =V
18 =V
19 = TC type
20 = TC type
21 = TC type
22 = TC type
When this parameter is modified, rL parameter will be re-aligned to it.
1604-1-BC.p65
11
5/16/00, 10:25 AM
J
K range N range
When this parameter is modified, rH parameter will be re-aligned to it.
0 / -100.0 / -100 / -100.0 / -100 / -100 / 0 / 0 / -199.9 / -200 / 0 / 12 / 0 / 4 / 0 / 1 / 0 / 2 / 0 / -150 / -150 / -150 /
P3 = Initial scale value
11
23=TCtype
24=TCtype
25 = RTD type
26 = RTD type
27=TCtype
28=TCtype
NOTE: selecting P1 = 0, 2, 4,
instrument set automatically P36 = FLtr. For all the remaining ranges it will set P36 = nOFL.
P2 = Decimal point position
For linear inputs it is programmable from -1999 to 4000.
For TC and RTD input it is programmable within the input range.
P4 = Full scale value
For linear inputs it is programmable from -1999 to 4000.
For TC and RTD input it is programmable within the input range.