Page 185 - 2022-23 Auto Performance Drag Racing

Driveshaft Safety Loop
DRAG RACING
Bolt-in safety loop provides
driver protection in the event
of a driveshaft or U-joint fail-
ure. CNC-formed, 1/4" steel plate
installs in the driveshaft tunnel. Sold
complete with necessary hardware.
Offered with black hammertone or red powder-coated finish.
Rear Toe Rods
Heavy-duty steel rear toe rods are
fitted with polyurethane bushings (unless specified), eliminat- ing deflection for harder launches and reduced wheel hop. Choose from 1" x 2" boxed steel non-adjustable or tubular, 1-1/4" diameter x .120" wall adjustable versions. Offered with choice of black hammertone or red powder-coated finish.
Application Black Part No. Red Part No.
Vertical Links for 2015-20 Ford Mustang
Rigid 6061-T6 billet aluminum vertical
links directly replace the deflection prone
stamped steel units, reducing wheel hop and increasing per- formance. Choose from vertical links with spherical bearings or spherical bearing/Delrin bushing. Sold per pair.
2016-20 Chevy Camaro, Adjustable with Rod Ends
—
BMRTR007R
2010-15 Chevy Camaro, Boxed Non-Adjustable
BMRTR002H
—
2010-15 Chevy Camaro, Adjustable with Rod Ends
—
BMRTR004R
2015-17 Ford Mustang, Adjustable with Single Rod End
BMRTR005H
BMRTR005R
Application
Xtreme Anti-Roll Bar Kits
Black Part No.
Red Part No.
2011-17 Ford Mustang
BMRDSL017H
BMRDSL017R
2016-Up Chevy Camaro
—
BMRDSL019R
2015-20, Dodge Challenger/Charger
—
BMRDSL110R
Engineered
to eliminate
body roll
on launch,
kit provides increased traction and more consistent ET’s. Manufactured from heavy-wall, 1-3/8" diameter DOM tubing, complete with polyurethane bushings and adjustable end links. Sold in red powder-coated finish.
Part No.
Front Strut Tower Brace For 2008-20 Dodge Challenger/Charger
NEW!
Manufactured from rigid,
corrosion-resistant stainless
steel, strut tower brace is a direct bolt-on item that increases chassis rigidity, thereby improving vehicle handling. Fits all 2008-20 Dodge Challenger and Charger.
Torque Box Reinforcement Plate Kit for
1979-2004 Ford Mustang BMRTBR001 NEW!
Designed from CNC-laser cut,
CNC-formed steel plate, these
braces will bolt right into the
1979-04 Mustang with very little
fabrication required, adding extra
strength to both the upper and
lower control arm mounts. This
kit includes plates and all neces-
sary hardware needed for installation. If the vehicle makes extreme amounts of power, or is used primarily for racing, the reinforcement plates can be welded in for additional strength. Bare finish. Made in USA.
Transmission Conversion Crossmembers NEW!
These bolt-in crossmembers
replace the stock factory cross-
members allowing transmission
conversions without modifying
the factory part and possibly
damaging the transmission due
to mis-alignment. Black hammertone or red. Made in USA
Part No. Description
Description
BMRTCA045
Vertical Link, Spherical Bearings
BMRTCA046
Vertical Link, Spherical Bearing/Delrin Bushing
Part No. BMRXSB004R
Torque Arms for GM F-Body
Application
2010-15 Chevy Camaro
Heavy-duty, .120" wall DOM steel
Torque Arms, complete with
1/4" CNC-formed steel
plate and polyurethane
bushings, are significantly
stronger than the OEM torque arm, reducing the associated deflection and wheel hop. Adjustable units allow fine-tuning of pinion angle. Black hammertone or red powder coat finish.
Application
Black Part No.
Red Part No.
1982-02 Chevy Camaro/Pontiac Firebird, Adjustable
BMRTA001H
BMRTA001R
1982-02 Chevy Camaro/Pontiac Firebird, Non-Adjustable
—
BMRTA002R
1993-02 Chevy Camaro/Pontiac Firebird, Adjustable
—
BMRTA012R*
*Includes built-in driveshaft safety loop. Must be used with aftermarket exhaust.
Panhard Rods
Heavy-duty, 1-1/4" diameter x .120" wall tubular steel panhard rods directly replace the deflection prone OEM units, solidly locating the rear end housing. Offered in adjustable or non- adjustable versions, panhard rods are fitted with polyure- thane bushings (unless specified). Black hammertone or red powder-coated finish.
Application
Black Part No.
Red Part No.
1982-02 Chevy Camaro/Pontiac Firebird, Adjustable
BMRPHR002H
BMRPHR002R
1982-02 Chevy Camaro/Pontiac Firebird, Relocation Kit
BMRPHR004H†
BMRPHR004R†
2005-14 Ford Mustang, Adjustable
BMRPHR006H
BMRPHR006R
2005-14 Ford Mustang, Upper Panhard Rod Support
BMRPHR007H
BMRPHR007R
2005-14 Ford Mustang, Double Adjustable with Rod Ends
—
BMRPHR012R
BMRTC730H
1979-93 Ford Mustang, TH350/PG/700R4/C4/C6/ AOD/4L60E, Black Hammertone
BMRTC731H
1979-93 Ford Mustang, TH400/T-56, Black Hammertone
BMRTCC006R
1998-02 Camaro/Firebird, T56/M6, LS1. This crossmember is manufactured with a 3/16" laser-cut plate relocating the torque-arm to the crossmember.
†Relocation kit allows sufficient room for up to 3" exhaust routing over axle. No weld- ing or drilling required.
183
2022-23