Page 92 - Gaylor Blue Book

GPC -7000
GPC-6000-D
HOT WATER REQUIREMENTS: Provide a hot water supply to the H.W. Inlet on the Wash Control Cabinet. Water pressure at the inlet of the Wash Control Cabinet: 40psi min. – 80psi max. Water
HOT WATERteRmEpQeUrIaRtEuMreE:N14T0S°Fmin-180°Fmax. EquipmentPIPE SIZE Temp (°F) Pressure (PSI)
The Inlet pipe size may be from 3/4” to 1-1/4” depending upon Water Wash Ventilator or 140 min. 40 min.
equipment being served by this control cabinet. Consult factory
Water Wash Ventilator w/ UV 180 max. for pipe sizes.
80 max.
Water Wash Ventilator w/ UV 140 min. and Pollution Control 180 max.
60 min. 80 max.
30 min. 80 max.
40 min. 80 max.
HOT WATER OUTLET TO VENTILATOR(S)
Pollution Control Units
“Y” 34 Inches
Gaylord Duct Sumps
140 min. 180 max.
ELECTRICAL REQUIREMENTS
120 volt, 60Hz, 20 am14p0omrin. Pollution Control Units
220 volt, 50Hz, 20 am18p0 max.
PIPE SIZE Cabinet Size Chart
The Inlet pipe size may be from 3/4” to 1-1/2” depending upon equipment being served by this control cabinet. Consult facto“rXy ” for pipe sizes. Equipment
120 volt, 60Hz, 20 amp Non-Interrupted Service or
ELXC Clean In Place Ventilator
220 volt, 50Hz, 20 amp Non-Interrupted Service
CABINET SIZE CART
NUMBER ”X”
Gaylord Duct Sumps
OF SEQUENCES
Inches
34 48
(Inches)
ELECTRICAL REQUIREMENTS
GAYLORD COMMAND CENTER
OPTIONAL
LOW DETERGENT FLOW SWITCH
OPTIONAL LIGHT SWITCH
H.W. INLET
HOT WATER INLET
1-5 - Pipe Size = 11⁄4” Max.
1-4 - Pipe Size = 11⁄2” Max.
5 - Pipe Size = 11⁄2”Max.
40 48
A. Consult Factory for Cabinets with more than 5 Sequences
ELECTRICAL LEGEND
Form No. GPC-6000-D 0410-20233
© Copyright 2010, Gaylord Industries
Litho USA
Form No. GPC-7000 1018-20371
© Copyright 2018, Gaylord Industries
Litho USA
The manufacturer reserves the right to modify the materials and specifications resulting from a continuing program of product improvement or the availability of new materials.
ExhEau1s1t Fan(s) (If Specified, E2 Not Used.)
to Control Supply Fan(s) (If Specified, E2 Not Used.)
The manufacturer reserves the right to modify the materials and specifications resulting from a continuing program of product improvement or the availability of new materials.
NOTES:
B. Add 6” to the “X” Dimension if Cold Water Mist is added.
E1
120VAC 50/60Hz Service or
220VAC 50/60Hz Service Consult Factory for Cold Water Mist information.
Two Wires to Magnetic Starter(s) For Exhaust and ELECTRICAL LEGEND Supply Fans
E1
E2 E3
E4
E5 E6
E7 E8 E9
E10
E11 E12
E2
120EVA3C 50/60THwz oNoWni-rIentsetroruFpitredSSueprvpicresosrion System
220VAC 50/60Hz Non-Interrupted Service
E4 Up to Fifteen Wires and ground to Wash Solenoids
Two Wires to Magnetic Starter(s) For Exhaust and Supply Fans at Ventilators
Three Wires and ground, for DCA Control to Two Wires to Fire Suppression System
E5 Ventilator(s)
Five Wires and ground to the First Ventilator and
them Five WireOspfrtoiomnEaal c-hFViveentWilaitroersGarnodupgtrouthned, for UV System to
E6
Next VentilatoVr eGnrotiulaptor(s)
Two Wires and ground, for “Autostart” to Ventilator(s)
18” 30”
Optional - Up to Thirteen Wires and ground, for Optional - FivePWolilruetsioandCgoronutrnodl, Ufonr iUt(Vs)System to
E7
DRAIN TO FLOOR SINK
Ventilator(s) Optional - Two Wires and ground, from Light Switch
DRAIN TO FLOOR SINK
ELEVATION VIEW ELEVATION VIEW
E8
Optional - Up to Thirteen Wires and ground, for to Supply voltage service.
Pollution Control Unit(s)
Optional - Two Wires and ground, from Light Switch OptEio9nal - Two Wires and ground, from Light Switch
to Lights in Ventilator. to Supply voltage service.
24
“Y” (Inches)
36
48
Optional-TwoOWpitrieosnaanld-gTrwouonWd,irfreosmFrLoigmhtVSowltitcFhreeContactsTo
to Lights in Ventilator.
E10 Building Management System (BMS) to Control
Exhaust Fan(s) (If Specified, E2 Not Used.) Optional - Two Wires From Volt Free Contacts To
Building Management System (BMS) to Control
Optional - Two Wires From Volt Free Contacts To BMS
Optional - Two Wires From Volt Free Contacts To BMS
Optional - Two Wires to BMS To Monitor Fire Cycle If to Control Supply Fan(s) (If Specified, E2 Not Used.)
E12
Specified.
Optional - Two Wires to BMS To Monitor Fire Cycle If
Specified.