Page 381 - 2018 Racecar Engineering Open Wheel Parts and Accessories Catalog

Sprint Car 30" Torsion Bars 2-1/2" I.D.
Manufactured from 4340 aircraft grade steel these bars are heat Coil-Over Barrel Springs
treated, centerless ground, pre-stressed and powder coated. This Manufactured from exclusive H5S.
pre-stressing process virtually eliminates settling, increases bar TW material, Swift coil-over springs
strength and allows for more wheel travel before yielding. These are light, with consistent rate. Barrel
Sprint Car bars also feature quick safety clip ends, which rest inside design eliminates rate inconsistency
a groove along the outside of the splines. These clips meet all safety due to bowing, and issues with the
requirements and are rated for 7,000 lbs. of axial load. Sprint Car spring rubbing against the shock
bars are orientation specifi c. This means the bars marked LFRR may body. Springs have a maximum
be used in the left front or right rear and bars marked RFLR may be diameter of 4", measured at the
used in the right front or left rear. Sold each. Made in USA. center coil.
12" Tall 14" Tall
Rate Part No. Part No.
Part No. Description Length Rate
SWA300900T-LFRR Torsion Bar LFRR 30" 900 125 — SWI140-250-125B
SWA300900T-RFLR Torsion Bar RFLR 30" 900 150 — —
SWA300925T-LFRR Torsion Bar LFRR 30" 925 165 — SWI140-250-165B
SWA300925T-RFLR Torsion Bar RFLR 30" 925
SWA300950T-LFRR Torsion Bar LFRR 30" 950 175 SWI120-250-175B —
SWA300950T-RFLR Torsion Bar RFLR 30" 950 200 SWI120-250-200B SWI140-250-200B
SWA300975T-LFRR Torsion Bar LFRR 30" 975 225 SWI120-250-225B SWI140-250-225B
SWA300975T-RFLR Torsion Bar RFLR 30" 975 250 SWI120-250-250B SWI140-250-250B
SWA301000T-LFRR Torsion Bar LFRR 30" 1000 275 SWI120-250-275B SWI140-250-275B
SWA301000T-RFLR Torsion Bar RFLR 30" 1000
SWA301015T-LFRR Torsion Bar LFRR 30" 1015 300 SWI120-250-300B SWI140-250-300B
SWA301015T-RFLR Torsion Bar RFLR 30" 1015 325 SWI120-250-325B SWI140-250-325B
SWA301025T-LFRR Torsion Bar LFRR 30" 1025 350 SWI120-250-350B SWI140-250-350B
SWA301025T-RFLR Torsion Bar RFLR 30" 1025 400 SWI120-250-400B —
SWA301050T-LFRR Torsion Bar LFRR 30" 1050
SWA301050T-RFLR Torsion Bar RFLR 30" 1050
SWA301065T-LFRR Torsion Bar LFRR 30" 1065
SWA301065T-RFLR Torsion Bar RFLR 30" 1065

Circlip For Torsion Bars SWA81916-10
1-1/8". 10-Pack.
Oil Filters
Two-piece ribbed aluminum fi lter housing
contains a reusable, stainless steel mesh screen
element sealed with double O-rings. Filter has
a 1"-12 threaded inlet and is supplied with 2
adapters; a 3/4"-16 to fi t Ford or Chrysler and
Chevy Adjustable Pressure Oil Pumps a 13/16"-16 for Chevrolet. A built in high fl ow
bypass keeps maximum effi ciency to 5 microns
Cast oil pumps are adjustable from 75-125
PSI. Pumps are factory pre-set at 80 PSI and before activation. Independent tests have shown
include unique oil bypass anti-aeration diffusion the System 1 Filter to be six times less restrictive
screen for maximum effi ciency. Pumps accept than paper fi lters.
stock big block Chevy pickups. Part No. Description
SYS209-361-B Short Oil Filter, 3-7/8" Tall x 4-1/2" Dia.
Part No. Description
SYS234-900773-2 BB Chevy Oil Pump SYS209-561-B Tall Oil Filter, 5-7/8" Tall x 4-1/2" Dia.
SYS234-900775-2 SB Chevy Oil Pump SYS210-005 HP6 Replacement Filter, 1-1/2"-12 Threads
Replacement/Accessory Components
Billet In-Line Fuel Filters SYS205-0100 Spin-On Oil Filter O-Ring Kit
SYS214-0440 Bottom Plate Without Bypass
High-fl ow, high-capacity in-line fi lters use
pleated stainless mesh elements of the SYS216-0113 13/16" Reducer
same design as System 1 fi lters, only SYS226-90005-00 SB Chevy Oil Filter Block Adapter, Non-Bypass
with 30 micron confi guration. Ends are
machined for -6AN through -12AN fi ttings. SYS221-90004-12
Billet Remote Oil Filter Mounts
Part No. Description
SYS200-201406 2" Dia. x 4" Length, -6 Ends Billet aluminum remote oil fi lter mounts are
SYS200-201408 2" Dia. x 4" Length, -8 Ends red anodized for a professional appearance.
SYS202-202408 2" Dia. x 9" Length, -8 Ends Sold complete with required fi ttings.
SYS202-202410 2" Dia. x 9" Length, -10 Ends
Part No. Description
SYS202-202412 2" Dia. x 9" Length, -12 Ends
Replacement Element, SYS221-90004-10 Two-Bolt Flat Mount Style, -10AN
SYS208-101400 SYS221-90004-12 Two-Bolt Flat Mount Style, -12AN
2" Dia. x 4" Length Filters, 30 Micron
SYS222-90007-12 Two-Bolt Side Port Mount, LH Inlet, -12AN
380