Page 108 - C.C.Marine Parts & Accessories Catalogue

ROPE STEERING ACCESSORIES
CABLE CLAMP
Die Cast Zinc Chrome Plated Cable Dia. 3/16'' ORDER NO. 420-91852 (Pair)
TILLER ROPE SPRINGS
Electrogalvanized Steel
Normal Length: 5'' Compressed Length: 6'' Mfr. No. 091814-1 ORDER NO. 420-91814 (Pair)
Mfr. No. 091852-1
TILLER LINE CLAMP
Die-Cast ZAMAK For 3/16'' to 1/4'' diameter tiller line ORDER NO. 218-80430 (Pair)
Mfr. No. 8043-3
For more information see: www.attwood.com
For more information see: www.seadog.com
TILLER ROPE GROMMET
Molded of durable polyethylene. Has 3" opening and 5/16" inside flange. Uses #10 fasteners.
ORDER NO. 101-10153 White Grommet ORDER NO. 101-10155 Black Grommet
TILLER ROPE PULLEY
Stamped 304 Stainless - Nylon Sheave
ORDER NO. Mfr. No. A Wire B C D E Eye
Dia.
Strap
100-91934 091934-1 3/16" 2-7/16" 1-1/8" 3/8" 7/16" Yes
CABLE BOOT
This is truly a functional cable boot that is easy to install. No longer necessary to split or cut your motor well boot to pass cables through. This cable boot provides a fully open area to pass wiring and cables through and when rigging is complete simply pull cable tie snug around wires and cable to complete installation. The cable boot is constructed of rugged black vinyl that resists ultraviolet rays, gasoline and oil.
This cable boot is available in two sizes to cover all installation requirements. Patent Number 4,958,790.
CABLE BOOT 3"
ORDER NO. 205-90010 - Black ORDER NO. 205-90011 - White Requires a 3" diameter hole and mounts with 6 pan head screws.
T-H FLEXTM SLEEVING
• Lightweight sleeving • Protects wire, cables and hoses • Braided from high temperature yarn. • Expands up to four times its normal diameter
CABLE BOOT 4-1/2"
ORDER NO. 205-90040 ORDER NO. 205-90041 Requires a 4-1/2" diameter hole and mounts with 8 pan head screws.
ORDER NO.
205-00125
205-00150
205-00200
MOTORWELL BOOT
Mfr. No.
FLX-125-DP
FLX-150-DP
FLX-200-DP
Description
1-1/4" x 50' Flex Sleeving
1-1/2" X 50' Flex Sleeving
2" x 50' Flex Sleeving
For more information see: www.thmarine.com
Rigid, high-impact, non-corrosive, plastic reinforcing ring is molded into boot. This makes mounting easy, cost effective and water tight with only four #8 fasteners required.
ORDER NO.
Mfr. No.
A B Fastener
3" 3/16" #8RH
ORDER NO. 101-01511
Covers 3" hole
ORDER NO. 101-10151
Covers 4" hole
MOTORWELL BOOT
Molded Rubber
425-21630 521630-1
425-21655 521655-1
5-1/2"
3/16"
1/2"
9/16"
#8 RH
#8 RH
#8 RH
For more information see: www.detmarcorp.com
MOTORWELL BOOT SPLIT
Molded Rubber/Injection Molded Nylon 425-21663 521663-1 4-1/8"
425-21664 521664-1 5-1/2"
For more information see: www.sea-dog.com
74