Page 934 - 2019-2020 CCMarine Catalogue
P. 934

BILGE PUMPS/PWC PUMPS
BILGE PUMPS – LOPRO SERIES
LOPRO SERIES 900S
FULLY AUTOMATIC LOW PROFILE BILGE PUMP
Designed to bring automatic pumping power to tight spaces.
Rule’s LoPro Series Bilge Pumps are only 2.25” high. Yet each one can move a mighty 900 gallons per hour. In addition, the 900S model features two automatic modes. The first one engages the pump when the water level reaches 1.3" or 2", and the second one checks for water by briefly turning on the pump every 2.5 minutes.
• Fully rotating discharge body – The entire body swivels up to 180˚, making the pump extremely easy to install.
• Threaded discharge nozzle – The threads allow the discharge nozzle to couple with either a staight or 90˚ fitting, both of which are included. An included tricuspid check valve, used with the straight fitting, can be used to minimize the backflow of water.
• Multiple modes of operation – In addition to manual, the 900S features two automated modes of operation.
• Electronic automatic mode – The pump automatically turns on every 2.5 minutes to check for water, and if it’s detected the pump stays on until the water is gone. • High or low water sensing mode – The low setting automatically starts the pump
when the water level rises to 1.3", and the high setting engages the pump when the
water rises to 2". • Horizontal or vertical mounting – The 900S features a variety of mounting
ORDER NO.
272-09001
Mfr. No.
LP900S
SPECIFICATIONS:
Voltage: 12 VDC Flow: 900 GPH open flow at 13.6V Amp Draw: 4A approximate Protection: TCO Port Configuration: 3/4", 1", 1-1/8" Straight, 90˚ 3/4" Backflow preventer valve can be used with straight fittings Dimensions: 2.3"H x 9.3"L x 2.3"W
options to accommodate the boat’s design.
SPECIFICATIONS:
Voltage: 12 VDC Flow: 900 GPH open flow at 13.6V Amp Draw: 4A approximate Protection: TCO Port Configuration: 3/4", 1", 1-1/8" Straight, 90˚ 3/4" Backflow preventer valve can be used with straight fittings Dimensions: 2.3"H x 7.6"L x 2.3"W
LOPRO SERIES 900D
ORDER NO.
272-09002
Mfr. No.
LP900D
LOW PROFILE HIGH CAPACITY BILGE PUMP
Designed to bring pumping power to tight spaces.
Rule’s LoPro Series Bilge Pumps are only 2.25” high, but can move a mighty 900 gallons per hour. Each one features a threaded discharge nozzle with straight and 90˚ fittings, and the body can swivel up to 180°, making it a great fit for small spaces and odd configurations.
• 900 gallon per hour capacity – The 900D can move a colossal 900 gallons of water per hour, even though it has an extremely low profile.
• Fully rotating discharge body – The entire body swivels up to 180°, making the pump extremely easy to install.
• Threaded discharge nozzle – The threads allow the discharge nozzle to couple with either a staight or 90˚ fitting, both of which are included. An included tricuspid check valve, used with the straight fitting, can be used to minimize the backflow of water.
• Horizontal or vertical mounting – The 900D features a variety of mounting options to accommodate the boat’s design.
• 12V DC operation – The pump operates on standard marine electrical power while delivering high capacity pumping power.
AUTOMATIC PWC BILGE PUMP - 500 GPH 12 VOLT • Least amount of water in your PWC • No float switch needed
• Checks for water every 20 seconds • Completely submersible • Ignition protected • Non burn-out when dry
• Stainless steel shaft • Includes back flow preventer
ORDER NO.	Mfr. No.	GPH/LPH
272-61251-SA	25SA-6WC	500GPH/1893L
Amp Draw	Fuse (Max Flow)	Size
Port Size
Dimensions H x W x D
4.2" x 2.9" x 2.5"
1.6	4A
3/4" (19mm) NPSM 3/4" (19mm) Hose Barb
For more information see: www.xylem.com
902


































































































   932   933   934   935   936