Page 510 - CAT4

SET-UP WEDGES
Heavy Duty Machine Shop Tools
Product Code Length Width Thick End
WG-3 3 1 1⁄4 WG-5 5 1 1⁄2 WG-6 6 1 1⁄4 3⁄4
Features
• Set-up wedges are used for setting-up work on planers, shapers, milling machines and other similar applications.
WG-5
EYEBOLTS
Plain Pattern
Product Code
EB-1T EB-2T
EB-3T EB-4T EB-5T EB-6T EB-7T EB-8T EB-9T EB-10T EB-11T EB-12T EB-14T EB-15T EB-16T EB-17T
Shank Diameter (Inches)
1⁄4 5⁄16
3⁄8 7⁄16 1⁄2 9⁄16 5⁄8 3⁄4 7⁄8 1 11⁄8 11⁄4 11⁄2 13⁄4
Threads per Inch
20 18
16 14 13 12 11 10 9 8 7 7 6 5
Capacity of Vertical Load (lbs)
500
900 1,300 1,800 1,400 3,000 4,000 5,000 7,000 9,000 12,000 15,000 21,000 28,000 38,000 56,000
Length of Shank (Inches)
1 1 1/8 11⁄4 13⁄8 11⁄2 15⁄8 13⁄4 2 21⁄4 21⁄2 23⁄4 31⁄2 33⁄4 33⁄4 4 5
Inner Diameter (Inches)
3⁄4 27⁄32 1 1⁄32 1 1⁄16 11⁄8 11⁄4 1 5⁄16 1 17⁄32 1 5⁄8 1 3⁄4 1 15⁄16 2 5⁄32 2 7⁄16 2 25⁄32 3 5⁄32 4
Head Cross Section Thickness (Inches)
9⁄32 9⁄32
5⁄16 3⁄8 5⁄32 1⁄2 9⁄16 5⁄8 13⁄16 29⁄32 1 1⁄16 1 5⁄32 1 13⁄32 1 21⁄32 1 27⁄32 2 1⁄4
Overall Length (Inches)
21⁄4 2 5/8
2 29⁄32 3 1⁄4 35⁄8 3 31⁄32 43⁄8 4 25⁄32 5 9⁄16 6 1⁄8 6 7⁄8 7 1⁄2 8 13⁄16 9 7⁄8 11 13 1⁄2
Ultimate Strength (lbs)
2500 4500
6500 9000 12000 15000 20000 25000 35000 45000 60000 75000 105000 140000 190000 280000
2 41⁄2 21⁄2 4
ANSI Spec: B18.15 1985
Features
• Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage.
• Each lot is tested and inspected to insure conformance to specifications.
• Available with UNC Class 2A thread only.
• Plain pattern eyebolts must never be used to lift an angular load.
• Eyebolt shanks should never be undercut or eyebolt shank diameters reduced.
• To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed
to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load.
EYEBOLTS
Shoulder Pattern
EB-9T
Product Code
EB-21T EB-22T EB-23T EB-24T EB-25T EB-26T EB-27T EB-28T EB-29T EB-30T EB-31T EB-32T EB-34T EB-35T EB-36T
Shank Diameter (Inches)
1⁄4 5⁄16 3⁄8 7⁄16 1⁄2 9⁄16 5⁄8 3⁄4 7⁄8 1 1 1⁄8 1 1⁄4 1 1⁄2 1 3⁄4 2
Threads per Inch
20 18 16 14 13 12 11 10 9 8 7 7 6 5 4 1⁄2
Length of Shank (Inches)
1 11⁄8 11⁄4 13⁄8 11⁄2 15⁄8 13⁄4 2 21⁄4 21⁄2 23⁄4 3 31⁄2 33⁄4 4
Inner Diameter (Inches)
3⁄4 27⁄32 1 1 1⁄16 1 5⁄32 1 11⁄32 1 11⁄32 11⁄2 15⁄8 1 13⁄16 1 15⁄16 21⁄8 2 19⁄32 2 27⁄32 3 5⁄32
Head Cross-Section Thickness (Inches)
9⁄32 9⁄32 5⁄16 3⁄8 7⁄16 7⁄32 9⁄16 11⁄16 13⁄16 7⁄8 1 1⁄16 1 3⁄16 1 1⁄2 1 19⁄32 1 7⁄8
Overall Length (Inches)
2 7⁄16 2 7⁄8 3 11⁄32 3 23⁄32 4 1⁄32 4 13⁄32 4 3⁄4 5 11⁄32 6 6 3⁄4 7 1⁄2 8 3⁄8 9 3⁄8 10 3⁄4 12
Shoulder Width (Inches)
9⁄16 19⁄32 21⁄32 27⁄32 29⁄32 15⁄16 1 1⁄32 1 5⁄16 1 7⁄16 15⁄8 13⁄4 2 1⁄32 2 3⁄16 2 1⁄2 2 29⁄32
Ultimate Strength (lbs)
2500 4500 6500 9000 12000 15000 20000 25000 35000 45000 60000 75000 105000 140000 190000
ANSI Spec: B18.15 1985
Features
• Forgedfromthebestqualitycarbonsteel,hardenedandtemperedtoensureincreasedstrengthand toughness and reduce liability or breakage.
• Each lot is tested and inspected to insure conformance to specifications.
• Available with UNC Class 2A thread only.
• Eyebolt shanks should never be undercut or eyebolt shank diameters reduced.
• Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must
EB-29T
be reduced substantially. A steel washer or spacer may be required for proper seating.
• To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing
due to twist of cable. Tightness and seating must be checked after initial load.
510
TOOLS FOR SET-UP WEDGES/EYEBOLTS THE TRADES