Page 554 - IE.IE Limited - Sealey Tools Catalogue

554
Suspension Tools
1000kg
B
2250kg
A
A Hydraulic Coil Spring Compressor Model No. VS7011
Hydraulic hand pump unit powers 1000kg capacity ram and yoke assembly. Up to 50% faster than using other ratchet driven spring compressors. Equipped with two pairs of spring yokes with rubberised covers to prevent slippage and damage to springs. Suitable for springs from 80mm ID to 165mm OD.
Maximum Extension: Piston Travel:
Yoke Specification: Size:
Small Large
C
240mm 240mm
Capacity (Spring Diameter):
ID80-OD122mm ID110-OD165mm
B Coil Spring Compressor Kit 2250kg Model No. RE225
2250kg Maximum jaw loading with 2.9 x safety factor. Supplied with two pairs of drop-forged yokes. Safety yokes carefully shaped to prevent coil spring from bowing. Suitable for use with air impact wrenches. Wide availability of standard and optional yokes. Standard yokes included, order optional yokes in singles as required for application.
D NEW
C
Strut Nut Socket - Audi, VW
Yoke Specification: Size:
Small
Large
Model No. SX028
Suitable for the removal and installation of top shock
retaining nut. Location pegs fit into slots cut in the retaining ring and allow hex key access through the centre for release/adjustment of the shock. Use with 22mm spanner.
D Strut Nut Set 8pc Model No. SX0331
Comprehensive set for the removal and installation of nuts on McPherson struts. Covers a large range of vehicle applications.
Castellated Sockets:
Optional Yokes: Model No: 90.0060 (Single) 90.0070 (Single) 90.0090 (Single) 90.0100 (Single)
Spring Diameter:
Ø80-145mm (x2) Ø145-195mm (x2)
Size/Suitability:
Ø80-145mm for Conical Springs BMW; E39-46 Mercedes; E-Series, Type 211 Citroen/Peugeot; Break Rear Axle
Internal Diameter x Tooth Width:
E
Ø14.5 x 5mm
H
NEW
G
14.5 x 5mm
Drives:
Sizes (ID/Tooth Width): 12.5x3,12.5x3.5,14x2.5,14x5,14.5x5mm Ovals:
Drive:
Sizes (ID/Tooth Width):
15, 21, 22mm Ø10.5 x 3.5,
E
Strut Nut Tool Set 3pc - Audi, VW
1/2"Sq Ø7 x 5, 8.2 x 5.5mm
Model No. SX033
Suitable for the removal and installation of strut nuts on McPherson struts fitted to Audi and VW vehicles.
Internal Diameter x Tooth Width:
12.5 x 3.5,
F
Ø10.5 x 3.5,
F
Strut Leg Pry Socket 2pc 1/2"Sq Drive
G Rebound Spring Strut Tool Model No. VS392
Allows the piston to be held safely in the extended position when replacing internal rebound spring shock absorbers (MacPherson Strut). These shock absorbers are used to reduce vehicle roll and in some cases replace the use of the anti-roll bar which is becoming more popular on modern vehicles. Features a piston shaft clamp with nylon jaws and telescopic puller. Maximum Piston Shaft Size: Ø16.5mm Maximum Puller Extension: 60mm Applications: BMW, Fiat, Ford, Mercedes, Nissan, Peugeot, Toyota
H Shock Absorber Strut Nut Kit 18pc Model No. VS0331
Permits the removal of the top suspension nut by holding the strut piston, so it doesn’t rotate while turning the nut. The go-through design of the socket and ratchet allows the extension to pass through the middle. To be used in conjunction with a 1/2"Sq drive ratchet or T-bar (not included).
Contents:
Go-Through Ratchet: 21mm Go-Through 82mm Deep Sockets: 16, 17, 18, 19, 21, 22, 24mm
Extensions: Female Hex; 7, 8, 9mm, MaleHex;6,7,8mm,Slotted;5x8,6x8,7.1x9.6mm, TRX-Star*; T50
Model No. SX034
Reduces risk of damage to hub casting associated with using hammers and chisels to free the strut leg. Suitable for removal and installation of legs on most Audi, Ford, Peugeot, Renault, Seat, Skoda and VW. Sizes: 7 x 5mm, 8.2 x 5.5mm
sealey tools
@sealeytools
sealey tools
www.sealey.co.uk