Page 10 - SMOG DOCTOR - PRODUCT BROCHURE 2019

1) Injection Cleaning
 1a Petrol engine
First treatment: add the contents of one can of the VB35 cleaner and one of the VB26 to a minimum of 5 litres of petrol
already contained in the tank. Drive the vehicle as usual. Further treatment requires one can of VB35 added every 15,000
km to a minimum of 5 litres which is already in the fuel tank.
 1b Diesel engine
First treatment: add the contents of one can of the VB35 cleaner and one of the VB26 to a minimum of 5 litres of diesel
already contained in the tank or fill the new fuel filter with the VB35 cleaner. Drive the vehicle as usual. Further treatment
requires one can of VB35 added every 15,000 km to a minimum of 5 litres of diesel which is already in the fuel tank or fill
the new fuel filter with the VB35. Drive the vehicle as usual.
 1c LPG / Petrol engine:
At each service inject with the ‘GAS PUMP’ 75ml of the VB35 cleaner into the lpg-gas tank and pour the rest into the petrol
fuel tank.
 1d NCG / Petrol engine:
At each 60,000 km inject with the ‘GAS PUMP’ 300ml of the VB35 into the injector rail.
2 Water elimination
VB35 eliminates water from the whole petrol, diesel and lpg injection system by turning the water in tiny drops and covering them
with EP lubricants. The fuel pump and injectors are then “EP protected” and the humidity/moisture is then eliminated during the
combustion process.
3 Anti-freeze protection
Thanks to the elimination of the moisture and the contribution of some of the VB35’s components, the flock / freeze point of the
diesel fuel is lowered by 5ºC. VB35 also improves the cold start of lpg engines.
4 Lubrication cleaning - oil flush

At each service add the contents of one VB35 to 4-6 litres of the old oil in the engine.
In case of any doubt or in the case of notable deposits of black sludge if may be necessary to double or treble the dose of VB35.
Run the engine for approx.10 minutes but the longer the better and for extreme cleaning run for half an hour.
In order to clean the hydraulic valve lifters (tappets) raise the rpm above 1000 for short periods during this time.
Drain and replace oil and filter
5 Cleaning gearbox, abs & power steering

Add the contents of one can of VB35 to 4-6 litres of the old oil in the system to be cleaned. Drive the vehicle for 10 minutes.
Drain and replace oil and -filter.

6 Cleaning transmission
Add half a can to vb35 to the old oil. Drive the vehicle for about 10 minutes putting it thought all the gears.
Replace the oil and filter.
The traces of VB35 remaining are compatible with the seals in the system and will add only 1% of the total oil and will not alter its viscosity.
VB35 saves time and money by doing away with expensive cleaning machines.
7 Cleaning cooling system
Flushes oil and grease from the cooling system. After the repair, fill the cooling system with clean water and run the engine up to
operating temperature. Add the contents of one can of VB35 to the water. Run the engine on high revs for a MAXIMUM of 10
minutes. Drain and flush with clean water. Repeat if necessary.
8 Cleaning FAP/DPF filter and catalytic converter
Removes soot from the blocked FAP/DPF filters and catalytic converters. Remove the filter. Tap the bottom.
Pour half a can of VB35 into a 2 litre bottle and then top up with water, shake and pour mixture into the filter after blocking the other
end to hold mixture inside. Shake the filter and allow the VB35 to soak overnight (the longer the better) to soften and dissolve the
deposits.
The following morning shake and empty the filter into the waste oil container. Prepare another mixture and repeat the procedure
filling the filter from the opposite end. Wait at least four hours. Rinse out the remaining deposits from the filter with clean water.
9 Cleaning air conditioner
VB35 easily dissolves oil and moisture deposits. Inject 50 - 100ml of VB35 into the low pressure gas circuit of the air conditioner
and run the system at maximum Cold for 10 minutes. Remove the refrigerant gas and dry the circuit with compressed air.

10 Other uses

VB35 can also be used to remove asphalt from the paintwork of the vehicle but only if it has a clear coat. Contact us for more uses.