Page 523 - 2022-23 Auto Performance Drag Racing

Remote Battery Jumper Terminals
MOR74140
Place the battery anywhere in
the car and it will still be ac-
cessible between races for charging
with remote jumper terminals. Termi-
nals can be positioned in the most convenient spot,
inside or outside of the car, and connected to the battery with a high-amperage cable such as the Moroso MOR74005. Universal for 6-36-volt systems. Two per package.
Through-Panel Battery Connector
Used wherever a battery cable or other large
diameter, high-amperage cable, passes through a firewall or similar panel. Fits through 1-1/4" hole and is held solidly by included spanner kit. Use MOR74170 Battery Cable Remote Fitting End Kit to complete installation.
Part No.
Description
“A” (Dimensions) “B”
DRAG RACING
Solid Steel Motor Mounts
Replace stock rubber mounts to prevent torque loss and binding linkages caused by engine movement, and eliminate the need for torque straps or chains. Protective zinc finish. Sold in pairs.
Chevrolet
MOR62500
Replaces OEM 3990914, .250" Thick
1-11/16"
2-1/2"
MOR62510
Replaces OEM 3962748, .188" Thick
2-1/8"
2-3/8"
MOR62515
Replaces OEM 332648, .188" Thick
2-9/32"
2-3/8"
MOR62530
Replaces OEM 6258154, .188" Thick
1-3/4"
2-5/8"
Chrysler
MOR62540
1967-69 Cuda; 1967-72 Dart/Demon/Duster, .187" Thick
Ford
MOR62544
1979-83 Mustang/1993 Mustang, 5.0L, .187" Thick
MOR62545
1984-92 Mustang Hardtop/1990-92 Mustang Convertible, 5.0L, .187" Thick
Part No.
Starter Heat Shields
Description
Solid Steel Motor Mount Pad Kits
Mounts replace rubber-cushioned mounts on 1974-97 Camaro/Firebird and other GM cars with Chevrolet engines. Solid steel motor mount pads eliminate the need for torque straps, and prevent engine move- ment and linkage binding. Sold in pairs.
MOR74144
Red Through-Panel Battery Connector
MOR74145
Black Through-Panel Battery Connector
Excessive heat not only cuts short
the life of a starter, but also reduces
the starter’s cranking power. Starter
heat shields provide protection from
heat on race cars and tow vehicles.
Made of high-temperature insulating material sandwiched between two sheets of aluminum.
Part No. Description Battery Disconnect Switches
A battery disconnect switch is one of
the most critical safety devices in a
race car. Turning the non-slip handle cuts power to all electrical devices including ignition.
Part No. Description
Super-Duty Battery Disconnect Switch MOR74102
Super-duty switch includes two pairs
of copper studs for shutting down the
entire electrical system. Useful when
race car is fitted with an alternator. Rated
at 2,000 amps intermittent and 300 amps con- tinuous. Includes face plate and on/off decal.
Push/Pull Battery Disconnect Mounting Kit MOR74105
Mount to the roll
cage to actuate the
battery discon-
nect switch. 18" long black anodized link, equipped with
a T-handle, passes thru the rear panel to engage switch. Includes brackets, linkage, bushings, link, and fasteners. Use with MOR74100 or 74101 Battery Disconnect Switches.
MOR62630
Part No.
Description
MOR62610
1982-92 Camaro/Firebird SBC/BBC, Use with MOR62510
MOR62630
1974-81 Camaro/Firebird/1973-88 Malibu/Monte Carlo/ 1973-79 Nova, SBC, Use with MOR62515
Extra Long Bellhousing Dowel Pins
Simplify installation of bellhous-
ing to block. Quick, easy align-
ment of the transmission input
shaft will ensure clean clutch release, maximum pilot bearing life, and fewer shift problems. Fit most GM V8 and V6.
MOR74299
Fits SBC/BBC with Tilton Starter
MOR74300
Fits SBC/BBC with Delco Starter
Part No.
Roller Pilot Bearing MOR41100
Description
MOR37932
Standard, 1.500" Long
MOR37934
0.007" Offset, 1.328" Long
MOR37936
0.014" Offset, 1.328" Long
MOR37938
0.021" Offset, 1.328" Long
MOR74100
For Cars without Alternator, (2) Terminals
MOR74101
For Cars with Alternator, (2) Terminals
MOR74108
For Cars with Alternator, (4) Terminals
MOR74110
Protective Boots for Terminals, (1) Red and (1) Black
High-speed bearing is a direct replacement in all Chevy V8, 90° V6 and ’76 and later V6 Buick. Re- quires no modifications.
Perm-Align Transmission Gaskets
Truly reusable gaskets are manufactured using 40-durometer rubber that is vulcanized to a rigid steel frame. Gaskets may be installed or removed quickly, require no sealant, and are 3/16" thick. Sold each.
Part No.
Description
MOR93100
GM Powerglide
MOR93102
GM TH-350
MOR93103
GM TH-400
MOR93104
GM 700-R4/4L60E/4L65E
MOR93105
Ford E40D/4R100
MOR93106
Ford AOD/AODE/4R70W
MOR93107
Ford C-4
MOR93108
Ford C-6
MOR93110
Chrysler TF-727
521
2022-23