Page 76 - Equipment & Supplies
P. 76
Molding Supplies
76
Releases and Lubricants
WD-40 SLIDE NEXGEN METAL &
n Displaces Moisture. MOLD CLEANER
Formulated for ultra-high surface Direct alternative to trichloroethylene and
attraction to metal. It completely methylene chloride. Food approved. Leaves no
covers surfaces, including oily residue. No global warming compounds.
microscopic irregularities, even Not a hazardous air pollutant. Non-corrosive
in the presence of moisture. A and not SARA reportable. Biodegradable and
non-conductor of electricity and rinses with water. Meets tough health, safety
quickly eliminates moisture-induced and environmental regulations. High solvency
short circuits. for resins, polymers and dies. Formulated purely
n Penetrates. from citrus and vegetable products. It meets or
Ultra-high surface attraction results exceeds the toughest health and safety issues,
in a super penetrating action that loosens rust-to-metal bonds and frees without sacrificing RAW CLEANING POWER.
stuck, frozen, or rusted metal parts. Biodegradable, it easily rinses away with water
n Protects. and leaves no residue.
Deposits corrosion-resistant ingredients over the entire surface area, n General cleaning and wiping
including microscopic irregularities. This protective barrier shields against n Oil spill clean-up
moisture and other corrosive elements. n Ink, tar and adhesive removal
n Cleans.
Ultra-high surface attraction enables it to get under dirt, grime, caked n Paint and graffiti removal
grease, and oil to clean the surface at WD – the same time it forms a n Removing silicone and lithium grease
corrosion resistant barrier. n Degreasing
n Lubricates.
Ultra-high surface attraction assures the lubricating ingredients will be
widely dispersed and tenaciously held to all moving parts.
SLIDE ECONOSPRAY 6 COPPER & NICKEL ANTI-SEIZE
SILICONE MOLD RELEASE n Will not bleed, separate or harden
Works ef fi cient ly on both cold and hot molds. It is n Choose copper or nickel base
CFC-free and free of chlo ri nat ed solvents. Econo- n Copper rated to 2000˚F
Spray Silicone imparts a smooth, dry film, which Molding Supplies | Releases and Lubricants
®
is FDA approved and USDA ap proved for food n Nickel rated to 2800˚F
ma chin ery. Operating temps: 35˚F – 600˚F n Eliminates galling and seizing
n No ozone depleting chemicals n Suggested for nozzles,
screw tips, cylinder
n Non-chlorinated
bolts, mold
n No methylene chloride clamps, etc.
n No Chlorofluorocarbons (CFCs)
n Safe on solvent-sensitive plastics
SLIDE SUPERGREASE ...AND MUCH MORE
Colorless. Odorless. Non-toxic. FDA dielectric. Thousands of auxiliary items
Contains TPFE. Will not freeze, melt, gum up. available beyond these popular
Compatible with other lubricants No silicones. featured products. DME Molding
Will not wash out. USDA listed H1. Repels water. Supplies offers a wide variety
Will not separate, run or fall out. Thixotropic of other high-quality, low-cost
properties provide excellent mechanical releases /lubricants /cleaners,
stability when sudden temperature changes including RTV silicone, GoJo
®
occur. Exceptional load-bearing properties. Hand cleaners, Boltlockers,
Clear, clean, non-yellowing grease. For injection Metal Polish, TPFE thread
molds, mold as sem blies, especially medical and sealant (both liquid and tape),
food grade plastic parts. Prevents corrosion. and much, much more.
Oper. temps: -65° to +650°F
U.S. 800-626-6653 n Canada 800-387-6600 n sales@dme.net n www.dme.net