Page 172 - Microsoft Word - 2_Inch_Drain_Adapter_PDS_2016_01_05

FEATURES AND BENEFITS
Better Than Fasteners Low Rise Foam
• No damage to structural • Eliminates
decking minor surface
• Eliminates fastener back out irregularities
• No noise associated with No Solvents
Hurricane Force ® • No unsightly fasteners on • Low odor
drilling into concrete
•
VOC free
exposed decks
• No fastener or deck corrosion • No flame hazards
100% solids
•
PG-1 Pump Grade • High strength
Saves labor
•
Insulation Adhesive

PRODUCT DESCRIPTION
Weather-Tite Hurricane Force PG-1 Pump Grade Insulation
Adhesive is a two component, VOC free, all purpose, low
rise, bulk packaged, polyurethane foamable adhesive that
contains no solvents and sets in minutes.
APPLICATION
Application is quick and easy resulting in significant
labor savings for the contractor. Hurricane Force PG-1 1. Extend quick connect spouts in Part 1 and Part 2
Insulation Adhesive is dispensed through the Weather- box packaging. When using pails stir contents before
Tite Cyclone and Cyclone II pumps or an approved low material is poured into the holding tanks on approved
pressure pump cart which equally mixes Part 1 and Part pump machine.
2 of the adhesive, thus providing a quality, consistent 2. Invert box and place in tray on the Weather-Tite Cyclone
application each time. or Cyclone II pump. Box labeled Part 1 must be in area
of tray labeled “Part 1” and Part 2 in area labeled “Part
BASIC USE 2”.
Hurricane Force PG-1 Insulation Adhesive is designed for 3. If pails are used fill holding tanks as recommended by
use as an adhesive for bonding approved roof insulations pump manufacturer. Part 1 and Part 2 must be equally
to a building’s structural roof deck, base sheets, other mixed. If drums are used follow all recommendations
insulation boards, and smooth or graveled built-up roof provided by pump manufacturer.
surfaces. It is dispensed in 1/2” to 3/4” (1.27cm - 1.91cm) 4. Connect the black Part 1 fitting to the black feed hose
wide liquid beads that will quickly spread to a width of fitting. Connect the gray Part 2 fitting to the gray feed
2-3 inches. Hurricane Force PG-1 Insulation Adhesive will hose fitting. Operate pump according to manufacturer’s
expand and rise to fill minor surface irregularities. instructions.
5. Apply Hurricane Force PG-1 Insulation Adhesive directly
APPROVED INSULATIONS AND SUBSTRATES to the substrate, using a ribbon pattern. Space beads
• HD wood fiber • Lightweight insulating 12” o.c., to achieve proper coverage rates for insulation
• Polyisocyanurate concrete attachment.
• Perlite • Wood or steel 6. Hurricane Force PG-1 Insulation Adhesive should be
• Polystyrene • Modified Bitumen approximately 70°F (22°C) when being dispensed. As
• Gypsum cover boards membranes and base adhesive is applied, allow to begin rising, then place
• Asphaltic cover boards sheets (sanded or granule insulation board into adhesive. Do not allow the adhesive
• Concrete surfaced) to skin over. Eliminate uneven surfaces to ensure
• Gypsum • Approved insulations (multi- positive contact between the adhesive, insulation board,
• Cemetitious wood fiber layer applications) and substrate.
• Smooth or gravel surface 7. Unused material can be applied at a later date. Properly
built-up roof (re-roof clean dispensing wand and pump unit according to
applications) pump manufacturer’s recommendations.

For a complete list of approved substrates and insulation
types, or additional information, contact our Technical
Department.

WTT Systems - Roofing Division n A Millennium Adhesive Company n 888.564.9733 n wttus.com