Page 11 - 2017PL

®
®
Apollo® Slab Tech fabricated
Price per linear metre (all colours) includes standard edge detail)
Depth
300mm
600mm 750mm
1000mm £776
Return Ends
20mm Band 1 Veined
£262 £463 £581
£274 £485 £611
£815
30mm Band1 Veined
£315 £528 £660
£882
£331 £554 £695
£930
Depth
400mm 650mm 800mm
1100mm £854
20mm 30mm 20mm 30mm Band 1 Veined Band1 Veined Depth Band 1 Veined Band1 Veined
£311 £504 £618
£325 £529 £649
£898
£374 £572 £705
£972
£397 £601 £740
£1,023
500mm 700mm 900mm
£387 £542 £700
£932
£406 £570 £734
£982
£442 £616 £794
£1,063
£463 £649 £836
£1,122
Part Return £29 Full Return £48 Angled Return £62 Breakfront £102 Single Radius £93 Double Radius £138 Curved Front £206
End Panels Standard Butt (5mm overhang) /Flush Butt /Mitred Butt
Material square metre cost plus £176
Other Edge Detail/Inlay (price per linear metre)
Top or front Inlay £62 Sharks Nose £62 Milano (30/30) £124 Bullnose £46 Venetian (30/30) £124
Upstands/Splashbacks/Cladding (20mm thickness)
Square Upstand 3000 x 50mm £88 Splashback 3000 x 570mm £714 Cladding price per sq. metre £528
Square Upstand 3000 x 100mm £150 Splashback 600 x 750mm £230
Belfast Sink cut out (inc. drip groove) £141
Band 1
Veined
Band1 Veined
Sink / Hob Mountings & Cutouts
Sink overmount £73
Sink undermount £84
Drainers
Type A (1-5mm gradient) £62 Type D (3mm flat) £128 Type B (1-5mm gradient) £62 Type E (3mm flat) £128 Type C (1-5mm gradient) £62 Type F (flat with 3mm recess) £128 Solid Surface Sinks - white only (includes Basket Waste Strainer)
Single Bowl £204 One and a Half Bowl
1200mm
Hob Cutout** £97
Apollo® Urban Sinks R10s
(waste disposal units must be supported by a cradle)
£270
Cat No. Description
Length
Width
Depth Price
U851s Single Bowl U853s Half Bowl U871s Large Single Bowl U752s One & Half Bowl
317mm
413mm
175mm £713 150mm £575 210mm £804 175mm
168mm 500mm
352mm 413mm
317mm
413mm
£1134
168mm
352mm
150mm
The Urban sink which has a stainless steel base, is available in the colour of your choice to match or co-ordinate with your worksurface.
The top edge detail will be bevel edge unless otherwise stated.
Stainless steel bases can be susceptible to scratching.
There can be a slight variation in colour between sink and worktop. In order to avoid any colour variance between the top and the bowl, we suggest a bevel or moulded edge, if this is not specified, we will use our discretion as to which detail will be used.
sPlease advise position of the overflow when specifying an apollo® urban sink. Urban sinks are not available in disclaimer colours
Other items
Glue Cartridge use in silicone gun with adaptor (100ml sufficient for 3 joints or 12m of upstand) £33
Installation Care & Maintenance Kit (modular) £62 Care & Maintenance Kit £31
£91 £158 £763 £246 £550
Important Technical Note
** Includes insulation tape
Flush mounted or recessed hobs are not covered under warranty
apollo
by Sheridan
®
Important points to note
Measuring up
• Apollo® Slab Tech solid surface can expand as much as 1mm/mtr, so always allow a gap of at least 3mm if for example, worktops are captive between walls
• Tolerance in Apollo® Slab Tech solid surface is ±2mm
• Splashbacks and upstands over 100mm high must have a minimum gap from the face to the rear of the hob: Electric 50mm, Gas 100mm
• Allow a minimum 50mm from the cutout to the front edge
• Allow a minimum of 120mm between heated cutouts
• Joints should fall on a carcass end, giving added support to the joint
• Joints should never fall on cutouts and must be at least 100mm from sink or 120mm from hob cutout
• Overhangs in excess of 300mm should be supported and the worktop should be supported every 600mm
Hot Stuff
• Do not pour boiling hot water directly into solid surface sinks, and where constant boiling hot water taps are fitted, please ensure they are not left running directly into solid surface sinks
• Heat producing appliances that sit beneath the worktop, must have an aluminium foil membrane placed on the underside of worktop, directly above the appliance.
• Ensure that pans used on gas hobs are of correct size
• Hob flanges need to sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat & causing cracks in the worktop
• Flush mounted, recessed hobs (including induction hobs) are not covered under warranty
Installation
•Some colours have different levels of pigmentation (particles). This may lead to a variation in the aesthetic appearance of the worktop
• Plastering or tiling should be completed after installation
•Regular use of your Care &Maintenance Kit should ensure that your worktops always look good
• Installation is relatively easy, for either a competent DIy enthusiast or recognised kitchen installer to carry out
•Plan the worktop layout to ensure joints don’t fall on or within 100mm of cutouts.
• Easy to follow installation video is available to download at www.sheridan-uk.com
• Sheridan have fully qualified and vastly experienced installation teams throughout the UK, who will provide you with an excellent fitting service and support if required
Installation Training
Free installation training courses are available. Details can be obtained from our Customer Services Department
http://www.sheridan-uk.com/wp- content/uploads/SlabTechInstallGuide-v9-3-24-05- 2016.pdf
For further information Tel: 0845 618 2800 Fax: 0845 618 2824 sales@sheridan-uk.com www.sheridan-uk.com
11
slab tech