Page 17 - 2017PL

Return Ends 20mm 30mm 40mm 20+20mm
Full/Part Return £23 External Splay £44
Internal Splay £62
Break Front £137 Single Radius £91
Double Radius £163
Double Notch £33
Triple Notch £54 Curved £209
Legs/End Panels (cost of material per sq. mtr plus joint cost)
Edge Detail (per linear m) 20mm
Double Bevel £33 Single Pencil (6mm rad) £68 Double Pencil (6mm rad) £102 Full BullnoseΩ (19mm rad) £68 ImperialΩ £112 Single OvoloΩ £112 Sharks Nose £84
Birds Beak
MilanoΩ
venetianΩ VE
Underside Polish (50mm only) £35
Underside Polish (cost per sq. mtr) £165
Sink/Hob Cutouts 20mm
Unpolished £98
Polished £227
Square Polished†† £446
Polished Belfast £193
Recessed Hob†BE £548
30mm
£105
£251
£492
£205
£548
Upstands/Cladding± 20mm thick 1 2 3 4 5 6 7
£23 £46
£64
£139 £93
£190
£35
£56 £239
30mm
£35
£68 £102 £68 £123 £123 £84
-
-
-
£35
£165
40mm
£112
£277
£538
£217
£548
£23 £48
£66
£141 £95
£217
£38
£59 £269
40mm
£37
£68 £102 £68 £134 £134 £84
-
-
-
£35
£165
20+20mm
£98
£227
£446
£295
£548
£52 £83
£112
£273 £203
£287
£38
£59 £353
Standard Butt (5mm overhang)/ Flush Butt / Mitred Butt
material sq.mtr cost plus £176
20+20mm
£144 £144 £167 £203 £235 £235 £219
£135
£220
£417
£35
£165
30+30mm
£105
£251
£492
£319
£548
60mm upstands per linear metre
100mm upstands per linear metre £65 Cladding per square metre £325 Drainers (1-5mm gradient unless stated) & Tap Holes
5 groove Drainer ∆ ∆ £270
3mm Recessed Drainer (flat)
Other Items
£444
£53
£55
£67 £347
£58
£70 £395
£61
£72 £402
£63
£80 £486
£68
£87 £572
£83
£107 £693
5 groove Angled Drainer ∆ £444 Tap Hole £18 Socket £36
Pan Rests (per set of 6) stainless steel £211
Care & Maintenance Kit £32
Please note:
Ω Requires scribed joint
VE Venetian edge detail is only available in 30+30mm
† Flush mounted or recessed hob cut outs (including induction hobs) are not covered under the 10 year
warranty
†† Please specify if the sink has square corners (less than 15mm radius)
BE Requires a 2mm bevel edge
∆ Drainer grooves and recessed drainers on granite are slightly dull and may have a patchy finished
compared to the rest of the worksurface
± 20mm granite upstands are not from the same block as 30mm worktops and although we will endeavour to match these as close as possible, there may be a difference in both shade and pattern.
apollo
by Sheridan
®
Important points to note
Measuring up
• Granite worktops can expand as much as 1mm/mtr, so always allow a gap of at least 3mm if for example, worktops are captive between walls
• Tolerance in granite is ±2mm
• Standard overhang is 35mm from the carcass front, not the door.
• Overhangs in excess of 300mm should be supported
(a metal support frame is recommended for overhangs)
• The worktop should be supported every 600mm
•Wherever possible, joints in worktops should fall on a carcass end panel not in the middle, this gives additional support to a joint.
• Granite sink / hob cut outs are barred front & back (fitting of steel support bars to give additional support to cutouts), without steel support bars the length of a cut out is reduced considerably
• Allow a minimum 50mm from the hob or undermounted sink cutout to the front edge, 50mm from the back edge, 120mm between two hob cutouts (70mm between sink cut outs). Allow a minimum of 80mm from the polished sink cut out to the front edge
• Joints must be at least 100mm from sink or 120mm from hob cut-out.
• Splashbacks and upstands over 100mm high must have a minimum gap from the face to the rear of the hob: Electric 50mm, Gas 100mm
• Drainer grooves and recessed drainers may have a slightly duller appearance than the worktop
• Joints above appliances are acceptable provided front and back support rails are fitted
• Stainless steel sink cut outs are made to manufacturers recommendations
Hot Stuff
• Ensure that pans used on gas hobs are of correct size
•Never place hot pans or cooking equipment directly onto the worksurface (or into an empty sink). Always use a heat protection pad or a trivet with rubber feet for hot cook wear or leave pans etc to cool on the hob first
• Hob flanges need to sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat & causing cracks in the worktop
• Flush mounted, recessed hobs (including induction hobs) are not covered under warranty
Installation
• Regular use of your Care & Maintenance Kit should ensure that your worktop always looks good
• Although we will endeavour to supply product as close as possible to the sample in-store, variations in colour can occur. Please contact us for samples of current stock, as we cannot accept responsibility for differences between samples and stock once your worksurface has been manufactured
For further information Tel: 0845 618 2800 Fax: 0845 618 2824 sales@sheridan-uk.com www.sheridan-uk.com
17
granite