Page 15 - 2017PL

®
Apollo® Wood fabricated (includes initial sealing) (500grit finish) Price per square metre
Species
27mm Thick
40mm Thick
60mm Thick
Beech
Iroko
Tiger Walnut Oak
Maple Sapelli Cherry
Euro Walnut Teak
Wenge
£293
£525
£358
£381
£367
£358 £689 £471 £480 £528 £549 £583 £638 £661 £890
£464
-
- £689
£697
- £435 £462
- £898
- £658
-
-
-
Return Ends
£15 Single Radius £71 Curved
£44 Angled Return
£127 Breakfront (10mminternalradii)
£42 £74
Return Edge
Double Radius
Joints
£74 Butt (3 bolts) £74
material square metre cost plus £176
Scribe (3 bolts)
End Panel
Standard Butt (5mm overhang)
Edge Detail The following edges are priced per linear metre
Square
Single Bevel
Double Pencil Round
Single Spanish
venetian £222 £11
£15 £21 £31 £31
£15 Single Pencil Round £15 £21 Double Round £21
Single Round
Single Ovolo
Bullnose
Drip groove (3mm deep x 7mm wide) Drainers/Tap Holes
£31
Single Imperial £31
Drainer grooves per set £64 Sink/Hob Mountings & Cutouts
Tap Hole £15
Sink Undermount £75 Hob Cut-Out† £84
(including tape)
Other Items
Sink Overmount £44
Belfast Sink Cutout £93 (including Drip groove)
Aga/Oven End Cap
£66 Pan Rests per set of 6 Stainless Steel £92
(per end - 20mm strip)
Installation Care & Maintenance Kit
(200, 300 & 400mm long)
£89
Important Technical Note
† Flush mounted or recessed hob cut outs (including induction hobs) are not covered under the 10 year warranty
Sheridan endeavours to ensure that environmental impact is minimal when sourcing its timber, using only responsibly managed forestry products, wherever possible.
Sheridan 60mm wood worktops are certified by the FSC® Chain of custody SW-COC-000984 (licence No. FSC-C003167) Look for the FSC® logo to identify which items are available FSC® certified.
Download our Wood Installation leaflet here:
http://www.sheridan-uk.com/wp- content/uploads/Wood_Install_v2-0-120813.pdf
apollo
by Sheridan
®
Important points to note
Measuring up
• Our hardwood worktops are constructed from 40mm wide, finger jointed pieces of kiln dried timber
• Tolerance on bespoke wood ±2mm on blanks ±5mm
• Worktops can expand as much as 1mm/mtr in length, so always allow a gap of at least 3mm, between the worktop and the wall if for example, worktops are captive between walls
• Upstands should be fixed to the wall and NOT to the worktop. There should be a 3mm gap between the worksurface and upstand, the only connection between upstand and worktops should be silicone sealant, allowing the natural movement of your worktop
• Upstands over 100mm high must have a minimum gap from the face to the rear of the hob: Electric 50mm, Gas 150mm
• Allow a minimum 50mm from the cutout to the front edge
• Allow minimum 120mm between heated cutouts
• Allow minimum 100mm between sink cutouts
• Stainless steel sink cut outs are made to manufacturers recommendations
• Overhangs in excess of 300mm should be supported and the worktops should be supported every 600mm
Hot Stuff
• Heat producing appliances that sit beneath the worktop, must have an aluminium foil membrane placed on the underside of the worktop, directly above the appliance
• Ensure that pans used on gas hobs are of correct size
• Hob flange needs to sit on aluminium thermal insulation tape around the cut-out, to avoid conducting too much heat and causing cracks in the worktop
Installation
• Plastering or tiling should be completed after installation
• Timber worksurfaces must not be installed in unoccupied premises.
• If wood worktops are to be stored prior to installation, they should always be stored at room temperature away from all sources of heat and moisture, on a sound level surface horizontally with a minimum of four timber battens equally spaced in between each worktop and on the floor
• Never store in a garage or an unfinished building and always install within 7 days of delivery
• Seal regularly in the first couple of weeks after installation to avoid the worktops drying out
• To test if a worksurface requires further sealing, apply a drop of water to the surface, if the water pools the sealing requires further attention. If the water runs away, no more sealing is required.
• Regular use of your Care & Maintenance Kit should ensure that your worktops always look good and perform well
• Although we will endeavour to supply product as close as possible to the sample in-store, variations in colour can occur. Please contact us for samples of current stock, as we cannot accept responsibility for differences between samples and stock once your worksurface has been manufactured
• Installation is relatively easy, for either a competent DIy enthusiast or recognised kitchen installer to carry out
• Installation video is available to download www.sheridan- uk.com
• Sheridan have fully qualified and vastly experienced installation teams throughout the UK, who will provide you with an excellent fitting service and support if required
For further information Tel: 0845 618 2800 Fax: 0845 618 2824 sales@sheridan-uk.com www.sheridan-uk.com
15
wood