Page 23 - 2017PL

®
®
Return Ends
20mm 30mm 40mm 20+20mm
Full/Part Return
£23 £23 £23 £52 £44 £46 £48 £83 £62 £64 £66 £112 £137 £139 £141 £273 £91 £93 £95 £203 £163 £190 £217 £287 £33 £35 £38 £38 £54 £56 £59 £59 £209 £239 £269 £353
External Splay Internal Splay Break Front Single Radius Double Radius Double Notch Triple Notch Curved
Legs/End Panels (cost of material per sq. mtr plus joint cost)
Standard Butt (5mm overhang)/ Flush Butt / Mitred Butt material sq.mtr cost plus £176
20mm 30mm 40mm 20+20mm
Edge Detail (per linear m)
£33 £35 £37 £144 £68 £68 £68 £144 £102 £102 £102 £167 £68 £68 £68 £203 £112 £123 £134 £235 £112 £123 £134 £235
Double Bevel
Single Pencil (6mm rad) Double Pencil (6mm rad) Full BullnoseΩ (19mm rad) ImperialΩ
Single OvoloΩ
Sharks Nose
Birds Beak
MilanoΩ
venetianΩ VE
Underside Polish (50mm only) Underside Polish (cost per sq. mtr)
£84 £84
£84 £219 £135 £220 £417
£35 £165
£35 £165
Sink/Hob Cutouts
20mm 30mm
40mm 20+20mm 30+30mm
-
-
-
£35 £165
-
-
-
£35 £165
Unpolished
£98 £105 £227 £251 £446 £492 £193 £205 £548 £548
£112 £98 £105 £277 £227 £251 £538 £446 £492 £217 £295 £319 £548 £548 £548
Polished †† Square Polished Polished Belfast Recessed Hob†BE
Upstands/Cladding± 20mm thick
60mm polished upstand (linear mtr)
100mm polished upstand (linear mtr)
Cladding polished (square metre)
60mm leather/volcano upstand (linear mtr) 100mm leather/volcano upstands (linear mtr) Cladding leather/volcano (square metre)
Drainers (1-5mm gradient unless stated)& Tap Holes
1 2 3
Stellar
4 56
£81 £85 £87
£90 £111 £600
£99 £102 £113 £122 £130 £143 £659 £795 £875 £108 £118
£97 £102 £107 £452 £514 £558 £89 £97 £103 £110 £122 £134 £583 £710 £822
£141 £157 £895 £1,069
-
-
-
-
5 groove Drainer ∆ £270 5 groove Angled Drainer ∆ £444
3mm Recessed Drainer (flat) ∆ £444
Tap Hole £18
-
Socket £36
-
Other Items
Pan Rests (per set of 6) stainless steel £211
Care & Maintenance Kit £32
Please note:
Ω Requires scribed joint
VE Venetian edge detail is only available in 30+30mm
† Flush mounted or recessed hob cut outs (including induction hobs) are not covered under the 10 year
warranty
†† Please specify if the sink has square corners (less than 15mm radius)
BE Requires a 2mm bevel edge
∆ Drainer grooves and recessed drainers on granite are slightly dull and may have a patchy finished compared to the rest of the worksurface
± 20mm upstands are not from the same block as 30mm worktops and although we will endeavour to
match these as close as possible, there may be a difference in both shade and pattern.
Important points to note
Measuring up
• Apollo® Quartz worktops can expand as much as 1mm/mtr, so always allow a gap of at least 3mm if for example, worktops are captive between walls
• Tolerance in Apollo® Quartz ±2mm
• Overhangs in excess of 300mm need support
• The worktops should be supported every 600mm
• Wherever possible, joints in worktops should fall on a carcass end panel not in the middle, this gives added support to a joint.
• Plan the worktop layout to ensure joints don’t fall on or within 50mm of cutouts.
• Allow a minimum 50mm from the cutout to the front edge, 50mm from the back edge and 120mm between two hob cutouts
• Allow a minimum of 70mm between sink cut outs.
• Splashbacks and upstands over 100mm high must have a minimum gap from the face to the rear of the hob: Electric 50mm, Gas 100mm
Hot Stuff
• Hob flanges need to sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat & causing cracks in the worktop
• Never place hot pans or cooking equipment directly onto the worksurface (or into an empty sink). Always use a heat protection pad or a trivet with rubber feet for hot cook wear or leave the pans etc to cool on the hob first.
• Flush mounted, recessed hobs (including induction hobs) are not covered under warranty
Installation
• Plastering or tiling should be completed after installation.
• Drainer grooves and recessed drainers may have a slightly duller appearance than the worktop
• Stainless steel sink cut outs are made to manufacturers recommendations
• Always use a chopping board; whilst the surface is scratch resistant, it is not scratch proof.
• Care should always be taken to protect your worksurface from sharp or heavy items.
• Care should be taken with exposed edges as if caught accidentally chipping can occur
• Although we will endeavour to supply product as close as possible to the sample in-store, variations in colour can occur. Please contact us for samples of current stock, as we cannot accept responsibility for differences between samples and stock once your worksurface has been manufactured
For further information Tel: 0845 618 2800 Fax: 0845 618 2824 sales@sheridan-uk.com www.sheridan-uk.com
23