Page 25 - 2017PL

®
®
20mm 30mm 40mm
Return Ends
20+20mm
Full/Part Return £23 External Splay £44
Internal Splay £62
Break Front £137 Single Radius £91
Double Radius £163
Double Notch £33
Triple Notch £54 Curved £209
Legs/End Panels (cost of material per sq. mtr plus joint cost)
Underside Polish (50mm only) £35
Underside Polish (cost per sq. mtr) £165
Sink/Hob Cutouts 20mm
Unpolished £98
Polished £227
Square Polished†† £446
Polished Belfast £193
Recessed Hob†* £548
60mm Upstand (per linear mtr) £86 100mm Upstand (per linear mtr) £106 Cladding (per sq. mtr) £556
Drainers (1-5mm gradient unless stated)& Tap Holes
Other Items
30mm
£105
£251
£492
£205
£548
Upstands/Cladding± 20mm thick Band 3 Band 4 Band 5 Band 6 Band 1 Polish Polish Polish Polish Suede
£23 £46
£64
£139 £93
£190
£35
£56 £239
£165
£98 £124 £730
40mm
£112
£277
£538
£217
£548
£102 £130 £795
£23 £48
£66
£141 £95
£217
£38
£59 £269
£165
20+20mm
£98
£227
£446
£295
£548
£111 £146 £948
£52 £83
£112
£273 £203
£287
£38
£59 £353
Standard Butt (5mm overhang)/ Flush Butt / Mitred Butt
material sq.mtr cost plus £176
Edge Detail (per linear m) 20mm
Double Bevel £33 Single Pencil (6mm rad) £68 Double Pencil (6mm rad) £102 Full BullnoseΩ (19mm rad) £68 ImperialΩ £112 Single OvoloΩ £112 Sharks Nose £84
Birds Beak
MilanoΩ
venetianΩ VE
30mm
£35
£68 £102 £68 £123 £123 £84
-
-
-
£35
40mm
£37
£68 £102 £68 £134 £134 £84
-
-
-
£35
20+20mm
£144 £144 £167 £203 £235 £235 £219
£135
£220
£417
£35
£165
30+30mm
£105
£251
£492
£319
£548
£89 £110 £583
5 groove Drainer ∆ £270
3mm Recessed Drainer (flat) ∆ £444
5 groove Angled Drainer ∆ £444
Tap Hole £18
Socket £36
Pan Rests (per set of 6) stainless steel £211
Care & Maintenance Kit £32
≈
Please Note:
Ω Requires scribed joint
VE Venetian edge detail is only available in 30+30mm
∆ Drainer grooves and recessed drainers on ECO are slightly dull and may have a patchy finished
compared to the rest of the worksurface
Please Note: Recessed Drainers are undermounted
see www.sheridan-uk.com for details
† Flush mounted or recessed hob cut outs (including induction hobs) are not covered under the 10 year warranty
†† Please specify if the sink has square corners (less than 15mm radius)
* Requires a 2mm bevel edge
± 20mm upstands are not from the same block as 30mm worktops and although we will endeavour to
match these as close as possible, there may be a difference in both shade and pattern.
Important points to note
Measuring up
• ECO Quartz worktops can expand as much as 1mm/mtr,
so always allow a gap of at least 3mm if for example, worktops are captive between walls
• Tolerance in ECO Quartz ±2mm
• Overhangs in excess of 300mm need support
• The worktops should be supported every 600mm
• Wherever possible, joints in worktops should fall on a carcass end panel not in the middle, this gives added support to a joint.
• Plan the worktop layout to ensure joints don’t fall on or within 50mm of cutouts.
• Allow a minimum 50mm from the cutout to the front edge, 50mm from the back edge and 120mm between two hob cutouts
• Allow a minimum of 70mm between sink cut outs.
• Splashbacks and upstands over 100mm high must have a minimum gap from the face to the rear of the hob: Electric 50mm, Gas 100mm
Hot Stuff
• Hob flanges need to sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat & causing cracks in the worktop
• Never place hot pans or cooking equipment directly onto the worksurface (or into an empty sink). Always use a heat protection pad or a trivet with rubber feet for hot cook wear or leave the pans etc to cool on the hob first.
• Flush mounted, recessed hobs (including induction hobs) are not covered under warranty
Installation
• Plastering or tiling should be completed after installation.
• Drainer grooves and recessed drainers may have a slightly duller appearance than the worktop
• Stainless steel sink cut outs are made to manufacturers recommendations
• Always use a chopping board; whilst the surface is scratch resistant, it is not scratch proof.
• Care should always be taken to protect your worksurface from sharp or heavy items.
• Care should be taken with exposed edges as if caught accidentally can chip.
• Although we will endeavour to supply product as close as possible to the sample in-store, variations in colour can occur. Please contact us for samples of current stock, as we cannot accept responsibility for differences between samples and stock once your worksurface has been manufactured
For further information Tel: 0845 618 2800 Fax: 0845 618 2824 sales@sheridan-uk.com www.sheridan-uk.com
25