Page 27 - 2017PL

®
®
Return Ends
20mm 20+20mm
Full/Part Return
External Splay
Internal Splay
Break Front
Single Radius
Double Radius
Double Notch
Triple Notch Curved
Legs/End Panels (cost of material per sq. mtr plus joint cost)
Underside Polish (50mm only)
Underside Polish (cost per sq. mtr)
Sink/Hob Cutouts
Unpolished
Polished
Square Polished††
Polished Belfast
Recessed Hob†* £822 £822 Upstands/Cladding± 20mm thick 1 2 3
£35 £66
£93
£205 £137
£245
£50
£81 £314
£248
20mm
£147
£341
£669
£290
£78 £125
£168
£410 £305
£431
£57
£89 £530
Standard Butt (5mm overhang)/ Flush Butt / Mitred Butt
material sq.mtr cost plus £264
Edge Detail (per linear m)
Double Bevel
Single Pencil (6mm rad) Double Pencil (6mm rad) Full BullnoseΩ (19mm rad) ImperialΩ
Single OvoloΩ Sharks Nose
Birds Beak
MilanoΩ
venetianΩ
20mm
£50 £102 £153 £102 £168 £168 £126
-
-
-
£53
20+20mm
£216 £216 £251 £305 £353 £353 £329
£203
£330
£626
£53
£248
20+20mm
£147
£341
£669
£443
60mm Upstand (linear mtr)
100mm Upstand (linear mtr)
Cladding (per sq. mtr)
Drainers (1-5mm gradient unless stated)& Tap Holes
£90
£116 £702
£97
£127 £815
£103
£139 £934
5 groove Drainer ∆ ∆ £405
3mm Recessed Drainer (flat)
Other Items
£666
5 groove Angled Drainer ∆ £666 Tap Hole £27 Socket £54
Pan Rests (per set of 6) stainless steel £211
Care & Maintenance Kit £32
≈
Please Note:
Ω Requires scribed joint
≈ Venetian edge detail is only available in 30+30mm
∆ Recessed drainers on DEKTON® are slightly dull and may be patchy
† Flush mounted or recessed hob cut outs (including induction hobs) are not covered under the 10 year warranty
†† Please specify if the sink has square corners (less than 15mm radius) * Requires a 2mm bevel edge
Important points to note
Measuring up
• Dekton® worktops can expand as much as 1mm/mtr, so
always allow a gap of at least 3mm if for example, worktops are captive between walls
• Tolerance in Dekton® ±2mm
• Overhangs in excess of 300mm need support
• Should be supported every 600mm
• Allow a minimum 50mm from the cutout to the front edge, 50mm from the back edge and 120mm between two hob cutouts
• Splashbacks and upstands over 100mm high must have a minimum gap from the face to the rear of the hob: Electric 50mm, Gas 100mm
Hot Stuff
• Hob flanges should sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat
• Flush mounted, recessed hobs (including induction hobs) are not covered under warranty
Installation
• Plastering or tiling should be completed after installation.
• Drainer grooves and recessed drainers may have a slightly duller appearance than the worktop
• Stainless steel sink cut outs are made to manufacturers recommendations
• Although we will endeavour to supply product as close as possible to the sample in-store, variations in colour can occur. Please contact us for samples of current stock, as we cannot accept responsibility for differences between samples and stock once your worksurface has been manufactured
For further information Tel: 0845 618 2800 Fax: 0845 618 2824 sales@sheridan-uk.com www.sheridan-uk.com
27