Page 29 - 2017PL

®
®
20mm 30mm
Return Ends
20+20mm
Full/Part Return
External Splay
Internal Splay
Break Front
Single Radius
Double Radius
Double Notch
Triple Notch Curved
Legs/End Panels (cost of material per sq. mtr plus joint cost)
Underside Polish (cost per sq. mtr)
Sink/Hob Cutouts
Unpolished
Polished
Square Polished††
20mm
£98
£227
£446
£193
Polished Belfast
Recessed Hob†* £548 £548 £548
Upstands / Cladding (20mm thick) Band 1 Band 2 Band 3 Band 4 Snow White
£23 £44
£62
£137 £91
£163
£33
£54 £209
£165
30mm
£105
£251
£492
£205
£23 £46
£64
£139 £93
£190
£35
£56 £239
£165
20+20mm
£98
£227
£446
£295
£52 £83
£112
£273 £203
£287
£38
£59 £353
Standard Butt (5mm overhang)/ Flush Butt / Mitred Butt
material sq.mtr cost plus £176
Edge Detail (per linear m)
Double Bevel
Single Pencil (6mm rad) Double Pencil (6mm rad) Full BullnoseΩ (19mm rad) ImperialΩ
Single OvoloΩ Sharks Nose
Birds Beak
MilanoΩ
venetianΩ
Underside Polish (50mm only)
20mm
£33 £68 £102 £68 £112 £112 £84
-
-
-
£35
30mm
£35
£68 £102 £68 £123 £123 £84
-
£220
-
£35
20+20mm
£144 £144 £167 £203 £235 £235 £219
£135
£417
£35
£165
30+30mm
£105
£251
£492
£319
60mm Upstand (per linear mtr)
100mm Upstand (per linear mtr) £107 Cladding (per sq. mtr) £572 Drainers (1-5mm gradient unless stated) & Tap Holes
£87
£90
£112 £622
£90
£113 £633
£96
£122 £726
£548
£100
£129 £791
5 groove Drainer ∆ £270
3mm Recessed Drainer (flat) ∆ £444
Other Items
5 groove Angled Drainer ∆ £444
Tap Hole £18
Socket £36
Pan Rests (per set of 6) stainless steel £211
Care & Maintenance Kit £32
≈
Please Note:
Ω Requires scribed joint
≈ Venetian edge detail is only available in 30+30mm
∆ Drainer grooves and recessed drainers on Zodiaq are slightly dull and may have a patchy finished
compared to the rest of the worksurface
Please Note: Recessed Drainers are undermounted † see www.sheridan-uk.com for details
Flush mounted or recessed hob cut outs (including induction hobs) are not covered under the 10 year ††warranty
Please specify if the sink has square corners (less than 15mm radius) * Requires a 2mm bevel edge
ZODIAQ QUARTZ SURFACES
Important points to note
Measuring up
• Zodiaq® Quartz worktops can expand as much as 1mm/mtr, so always allow a gap of at least 3mm if for example, worktops are captive between walls
• Tolerance in Zodiaq® Quartz ±2mm
• Overhangs in excess of 300mm need support
• The worktops should be supported every 600mm
• Wherever possible, joints in worktops should fall on a carcass end panel not in the middle, this gives added support to a joint.
• Plan the worktop layout to ensure joints don’t fall on or within 50mm of cutouts.
• Allow a minimum 50mm from the cutout to the front edge, 50mm from the back edge and 120mm between two hob cutouts
• Allow a minimum of 70mm between sink cut outs.
• Splashbacks and upstands over 100mm high must have a minimum gap from the face to the rear of the hob: Electric 50mm, Gas 100mm
Hot Stuff
• Hob flanges need to sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat & causing cracks in the worktop
• Never place hot pans or cooking equipment directly onto the worksurface (or into an empty sink). Always use a heat protection pad or a trivet with rubber feet for hot cook wear or leave the pans etc to cool on the hob first.
• Flush mounted, recessed hobs (including induction hobs) are not covered under warranty
Installation
• Plastering or tiling should be completed after installation.
• Drainer grooves and recessed drainers may have a slightly duller appearance than the worktop
• Stainless steel sink cut outs are made to manufacturers recommendations
• Always use a chopping board; whilst the surface is scratch resistant, it is not scratch proof.
• Care should always be taken to protect your worksurface from sharp or heavy items.
• Care should be taken with exposed edges as if caught accidentally can chip.
• Although we will endeavour to supply product as close as possible to the sample in-store, variations in colour can occur. Please contact us for samples of current stock, as we cannot accept responsibility for differences between samples and stock once your worksurface has been manufactured
Visit our website www.sheridan-uk.com for more useful tips, if the answer’s not there, ask a question and we will endeavour to answer within 24 hours.
For further information Tel: 0845 618 2800 Fax: 0845 618 2824 sales@sheridan-uk.com www.sheridan-uk.com
29