Page 41 - Product Catalog 2020 FULL1_Neat

Insulation Piercing Connectors - Above Ground

Installs In Just Minutes
Saving Many Man-Hours On The Job

Eliminates Wire Stripping
Connecting & Taping of Split Bolts
and Adding Inhibitor
Can be installed on Energized
Circuits eliminating Power CONNECTORS
Shutdowns

Red ‘Turbo Spacer’ Blue Rubber Insert
B l u e R u b b e r I n s e r t
Allows for main wire to be inserted Replaces insulation when used on
Repl ac es in s u l atio n
& hand tightened, while spacer bare wire. sed to avoid any damage
w h en u s ed o n b are
holds the tap location completely on neutral messenger.
o
open for easy wire insertion w ire. U s ed t av o id
All models except 96102 & 96104 an y d am ag e o n
L e a v e b l u e i n s e r t
R e m o v e b l u e
‘Turbo’ n eu tral m es s en g er. Remove blue Leave blue insert if main
i n s e r t i f m a i n
wire is bare
Spacer insert if main i f m a i n w i r e i s
w i r e i s i n s u l a t e d b a r e
wire is insulated
O n l y o n M o d e l s 96 106 , 9 110, 96 112, 96 114
6 Only on Models 96106, 96110, 96114
1 - Determine direction for tap conductor 2 - Insert tap conductor, - Place connector on main conductor & tighten
to enter connector. making sure conductor is the bolt with a closed-end wrench
Remove and discard extra end cap. fully seated in end cap. or socket until top shear-head Before
nut breaks off. Torquing Insulation Piercing Connectors
After
Torquing

• Overhead services - both insulated & bare mains, above grade RD • Can be installed on energi ed conductors, however, the tap must
services, street lighting, non-tension splicing & tapping, insulated not be under load
replacement for split bolts, tapping without cutting the main, gutter taps • Corrosion-free connection is good for hot, cold, damp, & salty
• Double shear-head bolt guarantees correct tor ue every time, ensuring connections. Properly installed the connector seals water-tight.
a uality connection, & eliminating the possibility of hot spots, damaged • This is accomplished by a sealant gel, that during installation is
wires or loose connections compressed and forces sealant to protect the connection from
• No cable stripping re uired, simply insert the acketed cable into the oxygen and water. Copper teeth are tin plated, the connector
entry port & tighten with a 1/2 point socket bodies are made from-strength fiber-reinforced thermoplastic
• Turbo spacer allows tap side to remain open while you hand tighten and galvani ed steel bolts
the connector on the main wire (note models) • 8 B isted for copper to copper, aluminum to aluminum,
• The bolt and all external parts of the connector are completely isolated & copper to aluminum 00 Volt 1 °F (90°C) Rated,
from energi ed parts and the bolt is covered by the plastic shear-head. Meets ANSI C11 . re uirements
The installer has no contact with an energi ed part

Dimensions = Inches
Cat. Number Torque in Bolt Head Size Conductor Range Dimensions in Inches Box
No. Of Bolts inch lbs. Main AWG Tap AWG H W L Qty

96102 1 80 1/2 2/0-6 8-14 3.6 1.7 2.7 12
96104 1 80 1/2 750-3/0 10-14 4.3 2.4 2.8 12
96106 1 80 1/2 1/0-8 2-10 3.7 2.0 3.0 12
96110 1 125 1/2 1/0-8 1/0-8 3.7 2.0 3.0 12
96108 1 125 1/2 4/0-3 2-10 3.9 1.7 2.7 12
96114 1 160 1/2 250-4 4/0-6 4.3 2.4 3.2 12
96116 2 330 5/8 350-1/0 350-1/0 5.4 3.1 5.0 4
96118 2 330 5/8 500-2/0 4/0-4 5.4 3.1 5.0 4
96120 2 330 5/8 500-4/0 350-1/0 5.4 3.0 5.0 4
96122 2 330 5/8 750-250 500-250 5.6 3.6 5.7 4
A34

www.morrisproducts.com 1-888-777-6678