Page 479 - 2020-2021 Racecar Engineering Drag Racing Parts and Accessories Catalog
P. 479
2020 DRAG RACING
Sealed Battery Box Remote Bat tery Jumper Ter mi nals
MOR74051 MOR74140
Lightweight black polyethylene Place the battery anywhere in the car
battery box, ideal for locating and it will still be ac ces si ble between
the battery to the trunk, is races for charg ing with remote jumper termi-
completely sealed to prevent nals. Terminals can be po si tioned in the most con ve nient spot,
spills or gases from entering the inside or out side of the car, and connected to the battery with a high
driver compartment. Box will amperage cable such as the Moroso MOR74005. Universal for 6-36 Volt
secure a Series 24 battery and systems. Two per pack age.
is 10-1/2" deep, 13" wide and
9-1/2" tall. Includes mounting Through-Panel Battery Connector
hardware. Battery cable not included. Used wherever a battery cable or other large diam-
eter, high-amperage cable, passes through a firewall or similar panel.
Battery Cable Kit Fits through 1-1/4" hole and is held solidly by included spanner kit. Use
MOR74005 MOR74170 Battery Cable Remote Fitting End Kit to complete installation.
Battery cable kit will with stand the high Part No. Description
am per age needed to start high-per for- MOR74144 Red Thru Panel Battery Connector
mance racing en gines. Includes 20' of MOR74145 Black Thru Panel Battery Connector
2-gauge copper cable with four ter mi nal Starter Heat Shields
ends.
Excessive heat not only cuts short the life
of a start er, but also reduces the start er’s
Battery Cable Remote Fitting End Kit
crank ing power. Start er heat shields
MOR74170
provide pro tec tion from heat on race cars
Quality, screw-together bat tery cable ends for and tow ve hi cles. Made of high tem per a-
side-post batteries are ideal for splicing in battery ture in su lat ing ma te ri al sand wiched be tween two sheets of aluminum.
dis con nects, remote jumper terminals, or junction Part No. Description
blocks. Two per package. MOR74299 Fits SBC/BBC With Tilton Starter
MOR74300 Fits SBC/BBC With Delco Starter
Battery Post Boots
Battery Dis con nect Switches
MOR74114
A battery disconnect switch is one of the most
Molded plastic boots prevent accidental
shorts and fit over most non-disconnect top terminals. Compatible with 4- critical safety devices in a race car. Turning the non-
gauge and smaller cable. Boots may be folded back for battery post access slip handle cuts power to all electrical devices including ig ni tion.
Part No. Description
when charging, etc. Includes (1) red and (1) black boot.
MOR74100 For Cars Without Alternator, (2) Terminals
MOR74101 For Cars With Alternator, (2) Terminals
Battery Post Terminal End Kit MOR74108 For Cars With Alternator, (4) Terminals NEW!
MOR74110 Protective Boots For Terminals, (1) Red And (1) Black
MOR74175
Same as MOR74170 ex cept for top post Super-Duty Battery Disconnect Switch
batteries. Two per package. MOR74102
Super-duty switch includes two pairs of copper
Battery Quick Connect Plugs studs for shutting down the entire electrical
Quickly connect vehicle’s electrical system. Useful when race car is fitted with an
system to a battery alternator. Rated at 2,000 amps intermittent and
charger, generator, etc. 300 amps continuous. Includes face plate and on/off decal.
Tough polycarbonate plugs
have spring-loaded copper contacts. Push/Pull Battery Disconnect Mounting Kit
Part No. Description MOR74105
MOR74200 Battery Quick Connect Plug
MOR74201 Battery Mini Quick Connect Plug Mount to the roll cage
to actuate the battery disconnect switch. 18" long black anodized link,
equipped with a T-handle, passes thru the rear panel to engage switch. In-
cludes brackets, linkage, bushings, link, and fasteners. Use with MOR74100
or 74101 Battery Disconnect Switches.
478
