Page 141 - 2019 Allstar Performance Parts and Equipment Catalog

Ford 9" Floater Housings Custom Width Ford 9" Housing ALL68710

Housings are jig welded for correct alignment using a Housings for stock or floating axles can be built to any REAR ENDS & AXLES
select used center section, new 3" O.D. x 3/16" wall axle width and pinion location. Floating axle housings are
tubes and include gear case mounting studs, fill and drain available with Allstar/Howe/Port City, SCP or AFCO 5x5,
plugs. Note: Axles are sold separately. or Wide 5 Pins. Stock housings can be ordered with small
Ford, big Ford, or new style big Ford ends. Select used
Housing Width/Offset 2.0" Pin 2.5" Pin center sections, as well as new heavy Duty or “Hot Rod”
58"/Centered – ALL68820 † style center sections, may be specified. “Hot Rod” center
60"/Centered ALL68700 ALL68822 † section provides clearance for brackets or exhaust systems
60"/2" Offset ALL68702 – in street rods and vehicles with limited space. All housings
61"/Centered ALL68703 –
62"/Centered ALL68704 ALL68824 † have select used centers, new axle tubes installed and
62"/2" Offset ALL68706 – are jig-welded for straightness. To order, please call and
63"/2" Offset ALL68708 – request a special order form, fill
64"/Centered ALL68709 – in all of the required informa-
†NEW! tion and return to us with a
signature attached. Housings Scan for the
TECH TIP are non-returnable and offered Custom Width
Ford 9" Housing
on a special order basis only. order form.
Housing Measuring Diagram
(60"*)
Rear End Station Brackets ALL10178
(28"*) (32"*)
Stand adapter
brackets fasten to
To
Top Viewp V adjustable arms of
Front most engine stands.
Front Of Vehicle
Supports full size
car and light truck
rear axle housings
Engine Stand Not Included
when servicing or
Example: Bare housing ALL68702 is 60" from hub face
to hub face and the pinion is located 2" to the left of the replacing differential gear sets. Position housing onto
housing centerline when viewed from rear of housing.* arms and secure into place with included retaining straps.
(Engine stand sold separately).
Notes: Please measure and inspect housing before welding brackets or painting.
Housing is non-returnable if modified or custom. Welding suspension brackets
on rear end housings can cause warping. Check for straightness after welding.
These housings use Allstar ALL72100 inner grease seals.
Pinion Centering Jig ALL68370
*Dimensions for example only.
Pinion centering jig fastens to the rear end housing
Hot Rod Ford 9" Housings and locates the pinion centerline when building or
narrowing housings. Machined slots are designed
NEW! to retain most tape measure ends for accurate
measurements. Applications include GM 12 and
14-Bolt, Dana 44 and 60, Chrysler 8-3/4", and
Ford 8.8" and 9" housings.
Steel Hot Rod housings are built with all
new components. The pumpkin section
is centered, so the pinion yoke is offset Ford 9" Truss Support ALL68330
approximately 1" to the right allowing Weld-on support
for symmetric tube bracketry on each side. Includes vent, adds strength to
pumpkin studs and bearing retainer t-bolts. Tube diam- rear axle housing
eter is 3" with 3/16" wall thickness. Axles sold separately. and reduces
Width measurements are from axle flange to axle flange. unwanted flex
ALL68830 ..... 56" during extreme torque. Constructed of 12 gauge (.108")
ALL68332 ..... 58" steel. 36" long x 2" wide.
ALL68834 ..... 60"

www.allstarperformance.com 139