Page 135 - 2018 Allstar Performance Parts and Equipment Catalog

Ford 9" Floater Housing Kits Custom Width Ford 9" Housing ALL68710

Housings, for stock or floating axles, can be built to any REAR ENDS & AXLES
width and pinion location. Floating axle housings are
available with Allstar/Howe/Port City, SCP or AFCO 5x5,
Housings are jig welded for correct alignment using a or Wide 5 Pins. Stock housings can be ordered with small
select used center section, new 3" O.D. x 3/16" wall axle Ford, big Ford, or new style big Ford ends. Select used
tubes with 2" spindle pins and include fill and drain plugs. center sections, as well as new Heavy Duty or “Hot Rod”
Kits also include Allstar Performance 5x5 hubs with 2" style center sections, may be specified. “Hot Rod” center
bearings, seals, locking spindle nut kits, 8-bolt rotor rings, section provides clearance for brackets or exhaust systems
Wilwood .810" or 1.25" 8-bolt rotors, a rotor bolt kit and in street rods and vehicles with limited space. All housings
1" lug nuts. have select used centers, new axle tubes installed and
are jig-welded for straightness. To order please call and
Housing Kits With Kits With Bare Housing
Width/Offset Steel Hubs Aluminum Hubs Only request a special order form, fill
60", Centered ALL68720 ALL68740 ALL68700 in all of the required informa-
60", 2" Offset ALL68722 ALL68742 ALL68702 tion and return to us with a
61", Centered ALL68723 ALL68743 ALL68703 signature attached. Housings Scan for the
62", Centered ALL68724 ALL68744 ALL68704 are non-returnable and offered Custom Width
62", 2" Offset ALL68726 ALL68746 ALL68706 on a special order basis only. Ford 9" Housing
order form.
63", 2" Offset ALL68728 ALL68748 ALL68708
64", Centered ALL68729 ALL68749 ALL68709
Note: Axles are sold separately.
Rear End Station Brackets ALL10178
TECH TIP Stand adapter
Housing Measuring Diagram brackets fasten to
adjustable arms of
(60"*) most engine stands.
Supports full size
(28"*) (32"*) car and light truck
rear axle housings
when servicing or Engine Stand Not Included
Top View replacing differential gear sets. Position housing onto
Front Of Vehicle
arms and secure into place with included retaining straps.
(Engine stand sold separately).

Example: Bare housing ALL68702 is 60" from hub face
to hub face and the pinion is located 2" to the left of the Pinion Centering Jig ALL68370
housing centerline when viewed from rear of housing.* Pinion centering jig fastens to the rear end housing
and locates the pinion centerline when building or
Notes: Please measure and inspect housing before welding brackets or painting.
Housing is non-returnable if modified or custom. Welding suspension brackets narrowing housings. Machined slots are designed
on rear end housings can cause warping. Check for straightness after welding. to retain most tape measure ends for accurate
These housings use Allstar ALL72100 inner grease seals.
measurements. Applications include GM 12 and
*Dimensions for example only. 14-Bolt, Dana 44 and 60, Chrysler 8-3/4", Ford
8.8" and 9" housings.
Ford 9" Set Up Carrier
ALL14169
Set up carrier takes the place of the Ford 9" Truss Support ALL68330
gear set on Ford 9" rear end hous-
ings and will keep dirt and debris Weld-on support
out of the housing. A pinion adds strength to
bracket can be attached to the rear axle housing
cover so the J-bar or Panhard bar and reduces
can be mounted for car transportation. The tip of the unwanted flex
handle matches the centerline of the driveshaft U-joint during extreme torque. Constructed of 12 gauge (.108")
so driveshaft length can be easily measured. Gloss red steel. 36" long x 2" wide.
powder coated finish.

www.allstarperformance.com 133