Page 209 - 2018 Allstar Performance Parts and Equipment Catalog

Pin Type Cleco Fasteners Quick Turn Spring Fixture
Cleco pins permit quick, easy installation Accurately drill panels when installing
and removal of sheet metal during fitting. quick turn fastener springs. Start with ALL19407
Pins work with thicknesses up to 1/4". a 1/4" center hole and use the fixture
to locate and drill 1/8" holes for mounting
1/8" Dia. Pins 3/16" Dia. Pins the springs. Size listed is spring center to center
ALL18222 ..... 10-Pack ALL18226 ...... 10-Pack distance. TOOLS & PIT EQUIPMENT
ALL18223 ..... 25-Pack ALL18227 ...... 25-Pack
ALL18224 ..... 100-Pack ALL18228 ...... 100-Pack ALL19406 ..... Fixture For 3/4" Spring
ALL19407 ..... Fixture For 1" Spring
ALL19408 ..... Fixture For 1-3/8" Spring
TECH TIP
Drill holes one drill size smaller than the Cleco pin size to Spindle Checker Tools
assure a tight fit. Assure correct alignment of the upper
and lower ball joint when checking
Clamp Type Cleco Fastener for bent spindles. Insert slugs into
ALL18230 spindle and guide rod will fit
Use when drilling is not an option. Smooth through slugs if spindle
throat prevents paint damage, and spring exerts isn’t bent. Kits fit
strong clamping pressure. Throat depth is 1" with a most aftermarket race
maximum clamping range of 1/2". and GM stock metric spindles.
ALL11176 ...... Kit With GM Lower, 2" Taper
ALL11177 ...... Kit With Chrysler Lower, 1-1/2" Taper
Cleco Pliers ALL18220 ALL11184 ...... Kit For GM Metric, 2" Taper
Unique tool readily
installs and removes Related Parts
Cleco fasteners. ALL99140 ..... GM Lower Slug With Nut (2" Per Ft.)
ALL99141 ..... Chrysler Lower Slug With Nut (1-1/2" Per Ft.)
ALL99158 ..... GM Metric Lower Slug With Nut (2" Per Ft.)
Quick Turn Fastener Wrench ALL99142 ..... Upper Slug With Nut (1-1/2" Per Ft.)
ALL19400 ALL99159 ..... GM Metric Upper Slug With Nut (2" Per Ft.)
The Allstar quick turn fastener ALL99143 ..... Replacement Guide Rod
wrench fits slot head fasteners
and reduces the risk of body panel Taper Reamers
or fastener damage when using screwdrivers for loosening Repair or enlarge tapered holes to accept tie rod
or tightening. Features a non-slip handle. ends or ball joints. Reamers may be used in a
drill with a 1/2" chuck by removing the T-handle.
Quick Turn Spring Adjuster ALL11170 ...... Reamer, 7.15°, 1-1/2" Taper Per Ft.
ALL11172 ...... Reamer, 9.56°, 2" Taper Per Ft.
ALL19405
This tool is a must when adjusting tension Taper Reamer Specifications For Ball Joints
of quick turn springs. Simply turn knob on
adjuster to evenly pull or push spring without kinking or Part No. Taper Specs Part No. Taper Specs
breaking spring. Ball Joint Ball Joint
ALL56204 1-1/2" Per Ft. ALL56217 1-1/2" Per Ft.
ALL56206 2" Per Ft. ALL56218 2" Per Ft.
Transfer Punches ALL56208 2" Per Ft. ALL56220 2" Per Ft.
For use with quick turn fasteners, place transfer ALL56210 1-1/2" Per Ft. ALL56280 1-1/2" Per Ft.
punch in a weld plate or body panel. Position ALL56212 2" Per Ft. ALL56284 1-1/2" Per Ft.
panel over top of punch and lightly tap with a ALL56214 1-1/2" Per Ft. ALL56286 1-1/2" Per Ft.
–
1-1/2" Per Ft.
ALL56216
–
hammer leaving a mark on the panel where hole is
to be drilled. Ball Joint Spreader Tool ALL11174
ALL19402 ..... For 5/16" Fasteners Tool separates ball joint from the spindle. Inside of
ALL19403 ..... For 7/16" Fasteners
cylinder is shaped to fit over tapered stud of most
ball joints and presses against stud of other ball
joint. Not for use on FWD or 4WD applications. Tool
is 4" tall fully collapsed and 6" tall fully extended.
Related Part
ALL11175 ...... 1" Extensions (Set of two)
ALL11175

Mike “Opie” Spatola Photo: Jim DenHamer
www.allstarperformance.com 207