Page 75 - Kondor® KL 1 - E-1063 Programming and Operation Manual

FAULT RESET ESC CAPTURE 50 HZ 0 HZ 0 % STARTED @ ENTER 01

CARR DRIVE ARM DRIVE PUMP DRIVE DRIVE COMM DRIVE CODE = 0000 FAULT CODE = 0000 CLEAR ALARMS CARRIAGE ARM AMPS 0 PUMP AUTO CAPTURE ON FAULTS ONLY
FAULTS FAULTS MORE 0 TARGET POSITION 0 GFCI

ARM JAM LOW AIR CARR JAM GFCI ESTOP FAULT BREAKAWAY LOW WATER ALARMS DRIVE COM FAULT DRIVE COM FAULT LOW WATER BREAKAWAY LOW AIR GFCI CHECK THERMOSTAT LOW WATER BREAKAWAY DRIVE COM FAULT GFCI SONAR MEASURES 0 00 00 BACK
MAIN
- - - - - - 16:46 LOADER00 WASH PASS POSITION MAIN

M A I N B A C K
MORE 1:56p DEBUG
= - - 0

See Next Page for More on SETUP MISC PASSWORD RE-LOGIN LEVEL NONE WEEP OFF MODE - [SCALED] TEMP SCALE = - - 0, OUTSIDE TEMP 03 SONAR BACK ADDER 03 SONAR FRONT ADDER SONAR SONAR SETUP OFFSET 1 HEIGHT = 1 FLOOR 098 WINDOW ABOVE FLOOR 06 BELOW FLOOR 06 OFFSET 0 HEIGHT = 0 FLOOR 098 WINDOW ABOVE FLOOR 06 BELOW FLOOR 06 MISC TWO 12/12/11 CHANGE PASSWORD ESTOP FAULT EMAIL FAULTS PAGE FAULTS EMAIL DATA

MAIN BACK ENTER SONAR EXIT SONAR - DISABLED - DISABLED - ENABLED - DISABLED THERMAL- CYCLE - DISABLED BETWEEN CYCLES = 020 MIN THERMAL SECONDS = 10 EMPTY BAY FLUSH - DISABLED EMPTY BAY PURGE TIME 10 END CYCLE PURGE TIME 04 BACK MAIN
SETUP

APPLICATION SETUP EXIT OPERATION DIRECT SELECT INPUTS INITIALIZE MODEM

SETUP ADVANCED CONFIGURATION DOOR CONTROL MISC PAGER POS 1 PACKAGE 2 PACKAGE 3 PACKAGE 4 PACKAGE 025 = WASH IN USE PAGER SETUP = 0 - 000 - 000 - 0000 CALL OUT (2) = 0 - 000 - 000 - 0000 NUMERIC MESSAGE ACTIVATOR IS, 1

PACKAGE 1 - 8 ENTRANCE OPERATION POS MAIN X15 X16 X17 X20 BACK MAIN CALL OUT (1) 01 SITE # 030 CODE DELAY SEPARATOR * LONG DISTANCE LOCAL DIAL LENGTH 10 HANG UP TO COMPLETE BACK MAIN

RESET Belanger , Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681
MONITOR OUTPUTS CARRIAGE FIND LIMIT TODAY 0 0 0 0 0 0 0 0 0 ENTER LIMIT EXIT LIMIT ARM ENC PROX ARM P SIDE CARRIAGE FORWARD

CARR HOME JOG SPRAY ARM FWD
USER SCREEN SOFTWARE 1.00 (ONE ARM) LOGIC SOFTWARE 1.00. ARM = 1 WASH DATA 0 0 0 0 0 0 0 0 0 JOG SLOW FORWARD

MONITOR INPUTS ABOUT CARR ENCODER ENTER SONAR FLOOR EXIT SONAR FLOOR 0 POSITION CARRIAGE BACKWARD BACK
ALL HOME FORCE PACKAGE 1 PACKAGE 2 PACKAGE 3 PACKAGE 4 PACKAGE 5 PACKAGE 6 PACKAGE 7 PACKAGE 8 TOTAL SPRAY ARM BWD

MAIN MAIN A MAIN
B
USER

RESET WEEP DESELECT IMMERSION HEAT
MONITOR OUTPUTS CARRIAGE FIND LIMIT RESET LOW AIR ESTOP BREAKAWAY LOW WATER ENTER DOOR PHOTO EXIT DOOR PHOTO EXIT VPS SENSOR ENTER VPS PHOTO ENTER1 PHOTO EXIT1 PHOTO STOP ENTER SLOW ENTER FWD EXIT STOP EXIT BWD EXIT WASH IN USE PURGE HP SELECT LP DESELECT ROCKER ARM OFF ARCH OFF SMALL TANK RECLAIM PUMP SPEED 000 STORE PATTERN STORE PATTERN STORE PATTERN STORE PATTERN STORE PATTERN

CARR HOME JOG GFCI
USER INPUTS BACK MAIN OUTPUTS WASH 00 PASS 00 ENU ENS END EXU EXS EXD HORN BACK MAIN FORCE PATTERN MAKE CURRENT MAKE CURRENT MAKE CURRENT MAKE CURRENT MAKE CURRENT
KONDOR KL1 / E-1063 MODULE
MONITOR INPUTS ABOUT CARR ENCODER ENTER SONAR @ FLOOR EXIT SONAR @ FLOOR ARM ENCODER PROX ARM HOME ARM P SIDE CARR EXIT PROX CARR ENTER PROX BIT1 / BIN1 2 2 / BIN 4 3 / BIN 8 4 / BIN PRESOAK 1 PRESOAK 2 PRE WT / AIR N5 N6 TRI WT / AIR DRY AGENT SPOT FREE EXIT ARCH RUST INHIB BACK
ALL HOME FORCE FORCE ENABLE AND PUMP SPEED MUST BE SET FROM FORCE SCREEN

MAIN BIT BIT BIT SPARE N4 SPARE SPARE SEAL WAX X - WAX DRYER HP WAX MAIN

FAULTS 0 0 RESET ALL
E-STOP SETUP 0 CLEAR QUEUE TODAY 0 0 0 0 0 0 0 0 0 FORCE DISABLE PURGE HP SELECT LP DESELECT ROCKER ARCH OFF ARM OFF IMMERSION HEAT SMALL TANK RECLAIM PUMP STATION 0 PUMP SPEED

MAIN RETURN NORMAL ACCESS USER QUEUE 000000000 ENTER PACKAGE HERE WASH 0 WASH DATA 0 0 0 0 0 0 0 0 0 TOTAL MACHINE CYCLES 0 FORCE PTRN BACK MAIN

FAULT DATA LOADER IN BAY PACKAGE 1 PACKAGE 2 PACKAGE 3 PACKAGE 4 PACKAGE 5 PACKAGE 6 PACKAGE 7 PACKAGE 8 PRESOAK 1 PRESOAK 2 PRE WT / AIR SPARE N4 SPARE N5 SPARE N6 TRI WT / AIR DRY AGENT SEAL WAX X - WAX SPOT FREE EXIT ARCH RUST INHIB DRYER HP WAX SABER LIGHT 1MANUL127 REV 01
QUEUE MAIN MAIN