Page 588 - IE.IE Limited - Sealey Tools Catalogue

588
Pullers
A
5tonne
A
B
B
10tonne
A Triple Leg Hydraulic Puller 5tonne Model No. HP5
Heavy-duty triple leg 5tonne hydraulic puller. Suitable for pulling hubs, flanges, gears and bearings. Supplied with three 2-position puller legs and carry-case. Contents: 230mm Leg (x3), Triple Head, 5tonne Ram & Handle, 80mm Leg Connector (x6), Nut & Bolt (x6)
B Triple Leg Hydraulic Puller 10tonne Model No. HP10
Heavy-duty triple leg 10tonne hydraulic puller. Suitable for pulling hubs, flanges, gears and bearings. Supplied with three 2-position puller legs and carry-case. Contents: 325mm Leg (x3), Triple Head, 10tonne Ram & Handle, 115mm Leg Connector (x6), Nut & Bolt (x6)
HP5 and HP10 are supplied in sturdy carry-case.
E
C
10tonne
D
D Slide Hammer/Hub Puller Set Model No. VS3700
Designed for the removal of stubborn four and five stud hubs and brake drums on cars and light commercial vehicles. Includes 4.3kg slide hammer, manual force screw and two sizes of stud.
E Micro-Puller Model No. PS995
Designed for the fast and safe removal of small bearings. Screw press, operated by tommy bar or by 14mm drive, exerts up to 1tonne of pressure. Spring loaded and drop-forged legs are secured around the bearing or gear by a screw collar to prevent slipping and subsequent damage or injury. Supplied with thrust shaft extension and storage case.
C Hydraulic Hub Puller Set Model No. PS993
Chromed, heat treated S45C steel puller yoke with hydraulic ram. Suitable for four and five stud hubs. Hydraulic ram provides additional power to extract the most stubborn hubs. Supplied in storage case.
Stud Sizes:
Slide Hammer Travel: Hub Plate Thickness:
M12 x 1.5, M14 x 1.5mm 340mm 20mm
Suitable for the following ISO bearings:
606, 607, 609, 626, 627, 628, 629, 636, 637, 638, 639, 668, 688, 689, 697, 698, 699, 6001, 6002, 6003, 6200, 6201, 6202, 6300, 6301, 6302, 6800, 6801, 6802, 6803, 6900, 6901, 6902, 6903
Minimum Leg Spread:
Maximum Leg Spread:
Maximum Reach:
H Universal Bearing Packer Model No. VS7022
Suitable for packing bearings with an even spread of grease. Clean, quick operation simply place bearing on to the bottom cone, screw down the cone lid and pump grease into nipple. Works on most tapered roller bearings fitted on cars, boats, trailers, etc. Both cones feature knurled grips for use with oily fingers. Suitable for use with Sealey and other best selling grease guns. Maximum Cone Diameter: Ø104mm Shaft (H x Ø): 60 x Ø11mm
Ø19mm Ø45mm 71mm
G
H
F
F Bearing Separators
Model No. SEE BELOW
Forged steel jaws. Suitable for removing bearings,
gears and bushes from shafts.
Model No: Capacity: PS986 Ø30-50mm PS987 Ø50-75mm PS988 Ø75-105mm PS989 Ø105-150mm
G Air Conditioning Clutch Hub Puller/Installer
Model No. VS604
Deluxe kit for the removal and installation of the air conditioning compressor clutch hubs. Designed to fit Harrison, Nippondenso, Sanden, Tecumseh, York and Zexel, but is also suitable for other compressor manufacturers.
Contents: Puller Plate, Puller Plate Retaining Bolts M6 x 1.25mm, Adaptor Bearing, Adaptors; Blank, M22 x 1.5, M22 x 1.75, M24 x 1.5mm, Force Screws (x9)
sealey tools
@sealeytools
sealey tools
www.sealey.co.uk