Page 61 - Hot Runner & Control Systems 2020

®
Meteor Hot Runner Systems 49 59
Meteor 1 & 2 Ancillary Component Options

Locating Rings Machine Nozzle Seats

X 6.82mm/ SPH RAD.
.269in
1.500 D
C
28.58mm/ M20 X 1.5
.218 1.125in E THREAD
22.1mm / 31.75mm/1.25in
Y BOLT CIRCLE .870in
A
B +.13
H –.00
ITEM NO. Ø D Ø X Ø Y A Ø B C
38.1
EHL0253 101 MM 82.5 MM 95 MM 117 MM 139.5 MM 73 MM HEX
.12
3.990 IN 3.250 IN 3.750 IN 4.625 IN 5.495 IN 2.875 IN O.D.
Ø 1.38
EHL0255 101 MM 82.5 MM 95 MM 117 MM 139.5 MM 114 MM E FLOW CHANNEL SPHERICAL
3.990 IN 3.250 IN 3.750 IN 4.625 IN 5.495 IN 24.500 IN M10 X 1.5 THRU MM IN RADIUS
ITEM NO.
Ø 3.44
Includes (2) 1/2 inch long, 5/16 Flat Head Cap Screws. MNS0009 9 MM .354 IN 1/2 + 3/4 IN
MNS1009 9 MM .354 IN 15.5 MM
Center Support Pads MNS0012 12 MM .472 IN 1/2 + 3/4 IN
MNS1012 12 MM .472 IN 15.5 MM
H +.13
–.00
NOTE: Machine nozzle tip orifice to be matched prop-
erly with nozzle seat flow channel.
6.82mm/ SPH RAD.
.269in
Dowel Pins O.D.
M10 X 1.5 THRU
28.58mm/ M20 X 1.5
1.125in THREAD Ø 8mm/.315in
E
+.13
H –.00 22.1mm /
.870in
X Custom Hot Runner Systems | New Products
O.D. L
M10 X 1.5 THRU
1.500 O.D. D H L
MM
ITEM NO. MM IN DRILLED AND C’BORED FOR 1/4-20 ITEM NO. MM IN
IN
LOW HEAD SCREW “X” DEEP
C
ECB0468 30 1.181 20 .787 DRILLED AND C’BORED FOR 1/4-20 DP820 20 .787
LOW HEAD SCREW “X” DEEP Ø 8mm/.315in
.218 ECB0469 30 1.181 10 H .394 DP828 28 1.102
1.260
32
ECB0503 40 1.575 10 .394 H DP832 M6 THREAD
.19
.06 Ø 8mm/.315in Ø .78
Ø 1.41 Ø 1.75 Ø .78 L
NOTES: Y A BOLT CIRCLE
1. The M10 X 1.5 tapped hole is used to screw the center support
L B
pad to a plate for machining the pad to the correct height.
2. An 8mm dia. dowel pin is required for assembly. Manifold Thermocouple
M6 THREAD
Drool Ring M6 THREAD
Meteor ® Hot Runner Systems | Meteor 1 & 2 Ancillary Component Options
.12
Ø 1.38
ITEM NO.
Ø 3.44 ETC0252

ITEM NO.
EHL1003

U.S. 800-626-6653 n Canada 800-387-6600 n dme@milacron.com n www.dme.net

6.82mm/ SPH RAD.
.269in

28.58mm/ M20 X 1.5
1.125in THREAD
E
22.1mm /
.870in

DRILLED AND C’BORED FOR 1/4-20
LOW HEAD SCREW “X” DEEP
DRILLED AND C’BORED FOR 1/4-20
LOW HEAD SCREW “X” DEEP
H
H
.19
.06 Ø .78
Ø 1.41 Ø 1.75 Ø .78