Page 2 - Parker - Fulflo Poly-Mate Filter Cartridges

P. 2

®
™
Fulﬂ o Poly-Mate Filter Cartridges

SPECIFICATIONS Poly-Mate Xtra-Duty Cartridges Recommended Maximum Flow Rate
Materials of Construction Change Out P - 35psid (2.4bar) Maximum 10gpm per 10 in. length
Filter media and support layers Maximum Temperature - 200°F (93°C)
Polypropylene Maximum Temperature @ Flow Rate and Pressure Drop Formulas
Surface treatment 35psid (2.4bar) - 200°F (93°C) Flow Rate (gpm) = Clean ΔP x Length Factor
None (fusion-sealed), chemically inert Maximum P @ 70°F (21°C) Viscosity x Flow Factor
and neutral 90psid (6.1bar) Clean ΔP = Flow Rate x Viscosity x Flow Factor
Media protection Maximum ΔP @ 200°F (93°C) Length Factor
PM – polypropylene netting; 35psid (2.4bar) Beta Ratio (ß) =
PXD – polypropylene cage Upstream Particle Count @
Speciﬁ ed Particle Size and Larger
Pleat pack side seal - Fused polypropylene Performance Attributes Downstream Particle Count @
End caps - Polypropylene Dimensions Speciﬁ ed Particle Size and Larger
®
Seals - Buna-N, EPR, Silicone, Viton , PFA Cartridge Outside Diameter Percent Removal Efﬁ ciency = ß-1 100
®
encapsulated Viton O-rings, Polyethylene 2 ½ in (63.5 mm) ß
foam gaskets Cartridge Inside Diameter Performance determined per ASTM F-795-88. Single-Pass
DOE – 1 ⁄ 16 in (27 mm) Test using AC test dust in water at a ﬂ ow rate of 3.5gpm per
1
Recommended Operating Conditions 10 in (13.2 lpm per 254 mm) cartridge.
SOE – 1 in. (25.4 mm)
Poly-Mate Cartridges (Std.) Notes:
Change Out P - 35psid (2.4bar) Filtration Ratings 1. Clean ΔP is psi differential at start.
Maximum Temperature - 200°F (93°C) 99% at 0.5μm, 1μm, 5μm, 10μm, 30μm, 2. Viscosity is centistokes. Use Conversion Tables for other units.
Maximum Temperature @ and 60μm pore sizes 3. Flow Factor is ΔP/GPM at 1cks for 10 in. (or single).
4. Length Factors convert ﬂ ow or DP from 10 in (single length) to
35psid (2.4bar) - 125°F (52°C) required cartridge length.
Maximum P @ 70°F (21°C) Effective Filtration Area
2
2
60psid (4.1bar) Up to 6.0 ft /10 in (0.6m /254 mm)
Maximum ΔP @ 200°F (93°C)
10psid (0.7bar) Poly-Mate
Poly-Mate
Liquid Particle Retention Ratings (μm) @ Removal Flow Factors Length Factors
Efﬁ ciency of: (psid/gpm @ 1 cks) Inches Factor
ß=5000 ß=1000 ß=100 ß=50 ß=20 ß=10 Rating Flow 9 1
Cartridge
Absolute 99.98% 99.9% 98% 95% 90% (μm) Factor 10 1
PM/PXD005 3 3 0.5 .25 <0.1 <0.1 0.5 0.0900 19 2
PM/PXD010 5 4.5 1.0 0.5 0.2 <0.1 1.0 0.0530 20 2
PM/PXD050 15 10 4 2.0 0.7 0.25 5.0 0.0290 24 3
PM/PXD100 30 28 10 6 3 1.2 10.0 0.0068 30 3
PM/PXD300 45 43 30 18 8 4.5 30.0 0.0048 39 4
PM/PXD600 95 90 50 40 20 12 60.0 0.0030 40 4

Ordering Information
—
—

Cartridge Code Pore Size Nominal Length Core Seal Material End Cap Conﬁ guration Special Options
PM Standard CODE MICRON CODE INCHES (MM) CODE MATERIAL CODE MATERIAL CODE DESCRIPTION CODE DESCRIPTION
5
PXD Xtra Duty 005 0.5 9 9 ⁄8 (244) A Natural Polypropylene P Polyfoam AR 020 O-ring/Recessed cap B Bubble-point test
(PM core only)
(DOE gasket only)
010 1.0 10 9 13 ⁄16 (249) DO Double open end (DOE) R DI water rinse
Glass-ﬁ lled polypropyl- E EPR DX Double open end/extended core (5 minutes)
050 5.0 19 19 5 ⁄8 (498) F ene (PXD core only)
N Buna-N Individual Poly bag
20 19 15 ⁄16 (506) 120/120 (Filterlite LMO & Nuclepore Z6
100 10.0 304 stainless steel S Silicone LL only (PXD only)
G Polymeric Vessels)**
29 29 ¼ (743) (core only)
300 30.0 PFA LR 120 O-ring/Recessed (Nuclepore)** Individual Poly bag
30 30 1 ⁄16 (764) T Encapsulated Viton ® Z15 15/ctn. (20˝, 30˝, 40˝)
600 60.0 (222, 226 O-ring only)* PR 213 O-ring/Recessed cap (Ametek ® & (PXD only)
40 40 (1016) Parker LT Polymeric Vessels) **
V Viton ® TC 222 O-ring/Flat Individual Poly bag
Z30 30/ctn. (10˝)
X No seal material TF 222 O-ring/Fin (PXD only)
*PFA/Viton ® is O-ring only, T is SC 226 O-ring/Flat
expanded PTFE gaskets
SF 226 O-ring/Fin
**Available only in 9 5 ⁄ 8 ˝ (-9) and 19 5 ⁄ 8 ˝ (-10) lengths
© 2010 Parker-Hannifi n Corporation
Specifi cations are subject to change without notifi cation. domnick hunter Process Filtration - North America
For User Responsibility Statement, see www.parker.com/safety All Rights Reserved
Fulﬂ o is a registered trademark of Parker-Hanniﬁ n Corporation
Viton is a registered trademark of E.I. DuPont de Nemours & Co., Inc.
Ametek is a registered trademark of Ametek, Inc.
DS_IP_Poly-Mate Rev. A
29

1 2