Page 2 - Parker - Fulflo MegaBond Plus Cartridges

P. 2

®
™
Fulﬂ o MegaBond Plus Cartridges
Speciﬁ cations MBP Flow Factors MBP Length
(psid/gpm @ 1 cks) Factors
Materials of Construction: Flow Rate and Pressure Drop Formulas
Polypropylene: Rating Flow Length Length Flow Rate (gpm) = Clean ΔP x Length Factor
Microﬁ ber 100% melt blown construction (µm) Factor (in) Factor Viscosity x Flow Factor
Center Support Core/End Caps: MBP1 2.17 9.75 1.0 Clean ΔP = Flow Rate x Viscosity x Flow Factor
Natural polypropylene MBP3 1.60 10.00 1.0 Length Factor
Thermally Bonded Gaskets:
Polyoleﬁ n closed cell foam (DOE only) MBP5 0.90 19.50 2.0
1. Clean ΔP is psi differential at start.
MBP10 0.32 20.00 2.0
Maximum Recommended 2. Viscosity is centistokes. Use Conversion Tables
Operating Conditions: MBP15 0.16 29.25 3.0 for other units.
Temperature: MBP20 0.12 30.00 3.0 3. Flow Factor is ΔP/GPM at 1cks for 10 in
(or single).
@ 60psid (4.1bar): 80°F (27°C) MBP30 0.10 39.00 4.0 4. Length Factors convert ﬂ ow or ΔP from 10 in
@ 35psid (2.4bar): 160°F (71°C) (single length) to required cartridge length.
@ 15psid (1.0bar): 200°F (93°C) MBP40 0.05 40.00 4.0
Flow Rate: MBP70 <0.05
5gpm (18.9 lpm) per 10 in length
Recommended Maximum: MBP90 <0.04
Change Out ΔP: 35psi (2.4bar) MBP120 <0.03
Operating Pressure @ Ambient
Temperature: 60psid (4.1bar) Liquid Particle Retention Ratings (μm) @ Removal Efﬁ ciency of:

Dimensions: Cartridge ß=5000 ß=1000 | 99.0% ß=100 | 99% ß=50 | 98% ß=10 | 90%
1 in ID x 2- ⁄ 16 in OD 10, 20, 30 and Absolute
9
40 in continuous nominal lengths MBP1 1 0.9 0.5 0.4 0.2
Absolute Filtration Ratings: MBP3 3 2.8 1.9 1.7 0.8
1μm, 3μm, 5μm, 10μm, 15μm, 20μm,
MBP5 5 3.7 2.3 1.6 1.2
30μm, 40μm, 70μm, 90μm and 120μm
MBP10 10 9.1 8.0 7.8 6.7
Beta Ratio (ß) =
Upstream Particle Count @ Speciﬁ ed MBP15 15 12.0 9.6 8.9 7.2
Particle Size and Larger MBP20 20 18.3 13.0 12.5 8.7
Downstream Particle Count @ Speciﬁ ed MBP30 30 25.0 20.0 18.0 13.0
Particle Size and Larger MBP40 40 35.0 28.0 25.0 18.0
Percent Removal Efﬁ ciency = ß-1 100 MBP70 70 60.0 48.0 42.0 30.0
ß
Performance determined per ASTM F-795-88. Single-Pass MBP90 90 80.0 72.0 63.0 48.0
Test using AC test dust in water at a ﬂ ow rate of 3.5gpm per 95.0
10 in (13.2 lpm per 254 mm) cartridge. MBP120 120 105.0 85.0 70.0
Ordering Information

MBP M — —

Cartridge Code Micron Rating Nominal Length Support Construction End Cap Conﬁ guration Seal Material
MBP MegaBond Plus (Absolute) CODE INCHES CODE MATERIAL CODE DESCRIPTION CODE DESCRIPTION CODE MATERIAL
(μm)
9-4 9¾ " N Polypropylene Std. Double Open End (DOE) / None Polyfoam (DOE only)
1 None Polyfoam SSC SS inserted 226 O-ring/Closed
10 10" G 304 SS (Core Only) E EPR
3 AR 020/Flat (Gelman) SSF SS inserted 226 O-ring/Fin
19-4 19½ " N Buna-N
5 DO DOE STC SS inserted 222 O-ring/Closed
20 20" S Silicone (o-ring only)
10 DX DOE with Polypro extender STF SS inserted 222 O-ring/Fin
29-4 29¼ " PFA Encapsulated
15 LL 120 O-ring both ends** TC 222 O-ring/Flat T Viton ® (222, 226 O-
30 30"
ring only)
20 LR 120 O-ring/Recessed** TF 222 O-ring/Fin
39-4 39 " V Viton ®
30 Std. open end/Polypropylene
40 40 " OB TX 222 O-ring/Flex Fin
spring closed end
40
PR 213 O-ring/Recessed** XA DOE w/Extended Core
70
SC 226 O-ring/Flat
90 XB Ext. core open end/Polypropyl-
SF 226 O-ring/Fin ene spring closed end
120
** Available only in 9¾" (9-4) and 19½" (19-4) lengths.
© 2010 Parker-Hanniﬁ n Corporation Viton is a registered trademark of E.I. DuPont de Nemours & Co., Inc.
Process Advanced Filtration Division
All Rights Reserved
Speciﬁ cations are subject to change without notiﬁ cation
For User Responsibility Statement, see www.parker.com/safety SPEC-MBP 01/10
58

1 2