Page 2 - Parker - Fulflo Poly-Mate Filter Cartridges

P. 2

®
™
Fulﬂ o Poly-Mate Filter Cartridges

SPECIFICATIONS Poly-Mate Xtra-Duty Cartridges Recommended Maximum Flow Rate
Materials of Construction Change Out P - 35psid (2.4bar) Maximum 10gpm per 10 in. length
Filter media and support layers Maximum Temperature - 200°F (93°C)
Polypropylene Maximum Temperature @ Flow Rate and Pressure Drop Formulas
Surface treatment 35psid (2.4bar) - 200°F (93°C) Flow Rate (gpm) = Clean ΔP x Length Factor
None (fusion-sealed), chemically inert Maximum P @ 70°F (21°C) Viscosity x Flow Factor
and neutral 90psid (6.1bar) Clean ΔP = Flow Rate x Viscosity x Flow Factor
Media protection Maximum ΔP @ 200°F (93°C) Length Factor
PM – polypropylene netting; 35psid (2.4bar) Beta Ratio (ß) =
PXD – polypropylene cage Upstream Particle Count @
Speciﬁ ed Particle Size and Larger
Pleat pack side seal - Fused polypropylene Performance Attributes Downstream Particle Count @
End caps - Polypropylene Dimensions Speciﬁ ed Particle Size and Larger
®
Seals - Buna-N, EPR, Silicone, Viton , PFA Cartridge Outside Diameter Percent Removal Efﬁ ciency = ß-1 100
®
encapsulated Viton O-rings, Polyethylene 2 ½ in (63.5 mm) ß
foam gaskets Cartridge Inside Diameter Performance determined per ASTM F-795-88. Single-Pass
DOE – 1 ⁄ 16 in (27 mm) Test using AC test dust in water at a ﬂ ow rate of 3.5gpm per
1
Recommended Operating Conditions 10 in (13.2 lpm per 254 mm) cartridge.
SOE – 1 in. (25.4 mm)
Poly-Mate Cartridges (Std.) Notes:
Change Out P - 35psid (2.4bar) Filtration Ratings 1. Clean ΔP is psi differential at start.
Maximum Temperature - 200°F (93°C) 99% at 0.5μm, 1μm, 5μm, 10μm, 30μm, 2. Viscosity is centistokes. Use Conversion Tables for other units.
Maximum Temperature @ and 60μm pore sizes 3. Flow Factor is ΔP/GPM at 1cks for 10 in. (or single).
4. Length Factors convert ﬂ ow or DP from 10 in (single length) to
35psid (2.4bar) - 125°F (52°C) required cartridge length.
Maximum P @ 70°F (21°C) Effective Filtration Area
2
2
60psid (4.1bar) Up to 6.0 ft /10 in (0.6m /254 mm)
Maximum ΔP @ 200°F (93°C)
10psid (0.7bar) Poly-Mate
Poly-Mate
Liquid Particle Retention Ratings (μm) @ Removal Flow Factors Length Factors
Efﬁ ciency of: (psid/gpm @ 1 cks) Inches Factor
ß=5000 ß=1000 ß=100 ß=50 ß=20 ß=10 Rating Flow 9 1
Cartridge
99.98% 99.9% 99% 98% 95% 90% (μm) Factor 10 1
PM/PXD005 3 3 0.5 .25 <0.1 <0.1 0.5 0.0900 19 2
PM/PXD010 5 4.5 1.0 0.5 0.2 <0.1 1.0 0.0530 20 2
PM/PXD050 15 10 4 2.0 0.7 0.25 5.0 0.0290 24 3
PM/PXD100 30 28 10 6 3 1.2 10.0 0.0068 30 3
PM/PXD300 45 43 30 18 8 4.5 30.0 0.0048 39 4
PM/PXD600 95 90 50 40 20 12 60.0 0.0030 40 4

Ordering Information
—
—

Cartridge Code Pore Size Nominal Length Core Seal Material End Cap Conﬁ guration Special Options
PM Standard CODE MICRON CODE INCHES (MM) CODE MATERIAL CODE MATERIAL CODE DESCRIPTION CODE DESCRIPTION
PXD Xtra Duty 005 0.5 9 9 ⁄8 (244) A Natural Polypropylene P Polyfoam AR 020 O-ring/Recessed cap B Bubble-point test
5
(PM core only)
(DOE gasket only)
010 1.0 10 9 13 ⁄16 (249) DO Double open end (DOE) R DI water rinse
Glass-ﬁ lled polypropyl- E EPR DX Double open end/extended core (5 minutes)
050 5.0 19 19 5 ⁄8 (498) F ene (PXD core only)
N Buna-N Individual Poly bag
20 19 15 ⁄16 (506) 120/120 (Filterlite LMO & Nuclepore Z6
100 10.0 304 stainless steel S Silicone LL only (PXD only)
G Polymeric Vessels)**
29 29 ¼ (743) (core only)
300 30.0 PFA LR 120 O-ring/Recessed (Nuclepore)** Individual Poly bag
30 30 1 ⁄16 (764) T Encapsulated Viton ® Z15 15/ctn. (20˝, 30˝, 40˝)
600 60.0 (222, 226 O-ring only)* PR 213 O-ring/Recessed cap (Ametek ® & (PXD only)
40 40 (1016) Parker LT Polymeric Vessels) **
V Viton ® TC 222 O-ring/Flat Individual Poly bag
Z30 30/ctn. (10˝)
X No seal material TF 222 O-ring/Fin (PXD only)
*PFA/Viton ® is O-ring only, T is SC 226 O-ring/Flat
expanded PTFE gaskets
SF 226 O-ring/Fin
**Available only in 9 5 ⁄ 8 ˝ (-9) and 19 5 ⁄ 8 ˝ (-10) lengths
© 2010 Parker-Hannifi n Corporation
Specifi cations are subject to change without notifi cation. domnick hunter Process Filtration - North America
For User Responsibility Statement, see www.parker.com/safety All Rights Reserved
Fulﬂ o is a registered trademark of Parker-Hanniﬁ n Corporation
Viton is a registered trademark of E.I. DuPont de Nemours & Co., Inc.
Ametek is a registered trademark of Ametek, Inc.
DS_IP_Poly-Mate Rev. A
35

1 2