Page 2 - Parker - Fulflo ProBrand Filter Cartridges

P. 2

®
™
Fulﬂ o ProBond Filter Cartridges

SPECIFICATIONS Particle Removal Ratings ProBond Flow ProBond Length
Materials of Construction 2μm, 5μm, 10μm, 25μm, 50μm, 75μm, Factors Factors
1st stage Pre-fi lter wrap: 125μm and 150μm
Rating Flow Length Length
• Polyester/Acrylic long staple
Dimensions, in. (mm) (μm) Factors (in) Factors
fi ber blend 9
2nd stage Final Filter wrap: Outside Diameter: 2- ⁄ 16 in (65) 2 0.08 9 1.0
1
Inside Diameter: 1- ⁄ 8 in (28.6)
• Acrylic long staple fi ber 5 0.04 10 1.0
• Fibers impregnated with Phenolic Lengths: Nominal, 10, 20, 30 and 40 in.
10 0.02 19 2.0
Resin Environmental/Chemical
25 0.012 20 2.0
Compatibility
Type of Construction Classifi ed as a nonhazardous material 50 0.01 29 3.0
Coreless, one-piece, rigid resin bonded • Incinerable (8000 BTU/lb) 75 0.006 30 3.0
fi brous matrix • Crushable and shredable 125 0.0013 39 4.0
• Certifi ed silicone-free
Maximum Recommended 150 0.0010 40 4.0
Operating Conditions • Suitable for weak acids and
bases (pH 5-9) 200 0.0005
• Flow Rate: 5gpm per 10 in length
• Unsuitable for oxidizing agents 250 0.0001
(18.9 lpm per 254 mm length)
• Not recommended for FDA
• Temperature: 250°F (121°C) applications
• Maximum Recommended End Adapters Flow Rate and Pressure Drop Formulas
Change Out ΔP: 50psid (3.5bar)
• None on double open end style Flow Rate (gpm) = Clean ΔP x Length Factor
• Recommended Maximum • ABS (Acrylonitrile Butadiene Viscosity x Flow Factor
Differential Pressure: Styrene) for most applications Clean ΔP = Flow Rate x Viscosity x Flow Factor
Cartridge Pressure Resistance • Nylon (NTC) for aromatic solvents Length Factor
- 150psid (10bar) @ 70°F (21°C)
1. Clean ΔP ispsi differential at start.
- 125psid (8.6bar) @ 100°F (38°C) 2. Viscosity is centistokes. Use Conversion Tables for other units.
- 90psid (6.2bar) @ 150°F (65°C) 3. Flow Factor is ΔP/GPM at 1cks for 10 in. (or single).
4. Length Factors convert ﬂ ow or ΔP from 10 in. (single length) to
- 65psid (4.5bar) @ 180°F (82°C) required cartridge length.
- 25psid (1.7bar) @ 250°F (121°C)

Ordering Information
— —
PRO

Cartridge Code Micron Rating Nominal Length End Cap Conﬁ guration Seal Material
PRO ProBond Series (μm) CODE IN. mm CODE DESCRIPTION CODE MATERIAL
2 9 9-¾ 248 Std. double open end (DOE) Omit DOE and XA
Omit coreless
5 10 10 254 E EPR
CXC Extended tinned steel core
10 19 19-½ 495 N Buna-N
C Tinned steel core
25 20 20 508 S Silicone (O-ring only)
Single open end 222 o-ring/Flat
50 29 29-¼ 743 NTC PFA Encapsulated
cap (Nylon) T Viton ® (222, 226 O-
75 30 30 762 ring only)
Std. open end/Polypropylene
OB
125 39 39 991 spring closed end V Viton ®
150 40 40 1016 Single open end 222 O-ring/Flat
TC cap (ABS Plastic)
200
250 XA Poly extender
Extended core open end/
XB
Polypropylene spring closed end
Specifi cations are subject to change without notifi cation. © 2010 Parker-Hannifi n Corporation
For User Responsibility Statement, see www.parker.com/safety domnick hunter Process Filtration - North America
All Rights Reserved
Fulﬂ o is a registered trademark of Parker-Hanniﬁ n Corporation
Viton is a registered trademark of E.I. DuPont de Nemours & Co., Inc.
DS_IP_ProBond Rev A.

1 2