Page 436 - Icon Ridge Maintenance & Service Catalog

Cutting, Sanding, Sawing, Surface Treatment

Wire Brushes – Single Wire

• For removing rust, paint, primer, surface coatings, etc.
• For cleaning forms and cast iron parts
• For deburring surfaces
• For areas difficult of access e.g. inner edges, slots, chinks, etc.
5861 1 50
Technical Data 5861 1 50 5
5861 1 60
Art.-No. Fixing Ø Max. speed Wire Ø Width
mm mm mm mm 5861 1 60 1
5861 1 26 shaft 6 mm 26 15,000 0.15 2.5
5861 1 50 shaft 6 mm 50 15,000 0.30 10
5861 1 50 25 shaft 6 mm 50 15,000 0.20 2.5
5861 1 55 2 shaft 6 mm 55 15,000 0.30 10
5861 1 60 shaft 6 mm 60 15,000 0.30 10 5861 1 26
5861 1 60 1 shaft 6 mm 60 15,000 0.30 20 5861 1 50 25
5861 2 12 shaft 6 mm 12 20,000 0.30 - 5861 1 55 2
5861 2 20 shaft 6 mm 20 18,000 0.30 -
5861 2 28 shaft 6 mm 28 15,000 0.30 -
5861 4 65 female thread M 10 65 11,000 0.35 -
5861 5 80 female thread M 14 80 8,500 0.3 -
5861 3 50 shaft 6 mm 50 6,000 0.30 -
5861 3 75 shaft 6 mm 75 4,500 0.30 - 5861 2 12
5861 2 20
5861 2 28
Article No. Article Description QTY
5861 1 26 ROUND BRUSH ST/BR B2.5MM D26MM 1 z
5861 1 50 ROUND BRUSH ST B10MM D50MM 1 z
5861 1 50 25 ROUND BRUSH ST/BR B2.5MM D50MM 1 z 5861 3 50
5861 1 50 5 ROUND BRUSH ST/BR B2.5MM D50MM 1 z 5861 3 75
5861 1 55 2 ROUND BRUSH ST/BR B10MM D55MM 1 z
5861 1 60 ROUND BRUSH ST B10MM D60MM 1 z
5861 1 60 1 ROUND BRUSH ST B20MM D60MM 1 z
5861 2 12 END BRUSH ST D12MM 1 z
5861 2 20 END BRUSH ST D20MM 1 z
5861 2 28 END BRUSH ST D28MM 1 z
5861 3 50 CUP BRUSH ST D50MM 1 z
5861 3 75 CUP BRUSH ST D75MM 1 z
5861 4 65 CUP BRUSH ST M10 D65MM 1
5861 5 80 CUP BRUSH ST M14 D80MM 1 5861 4 65
5861 5 80
Wire Brush Turbo

• Practical steel round brush with mandrel
• Can be used on a cordless drill or an angular grinder (with thread
M14 x 1.5, max. 3,500 rpm)
• Don’t press too strongly, this only increases the wear of the wire
brush, it does not increase the work speed
• The open construction prevents residues from getting stuck
• Reliably removes rust, underbody sealant, paint, sealing gaskets etc.
• Hardly any warming of the processed areas
• Can be sharpened up to 10-times by counter-clockwise turning on a
grinding stone
• Maximum speed: 3,500 rpm
• Ø approx. 100 mm
• Shaft-Ø: 8 mm
• Rotation speed dependent roughness:
- 3,000 rpm comparable to a 60 grit sandpaper
- 800 rpm comparable to a 120 grit sandpaper
• Suitable grinding stone: Art.-No. 5352 3508

Article No. Article Description QTY
5861 6 100 WIRE BRUSH TURBO B20MM D100MM 1
5861 6 100 1 PK(5)WIRE BRUSH T.B20MM D100MM 1
5861 6 100 2 MANDREL FOR WIRE BRUSH TURBO 1
Contents Art.-No. 5861 6 100:
• 1× Mandrel
• 1× Wire brush Turbo
Contents Art.-No. 5861 6 100 1:
• 1× Mandrel
• 5× Wire brush Turbo

Technical data subject to change.
Availability subject to country specific rules and regulations. www.iconridge.com Source: Theo Förch GmbH & Co. KG 436