Page 711 - Icon Ridge Industrial Tools Catalog
P. 711
Tool clamping \ Tool chucks ISO 7388-1 SK 40/50
Combination shell end mill arbours (DIN 6358) (ISO 7388-1)
SK SK Form G 6,3 ISO
40 50 AD 15000 rpm 7388-1
Application: Delivery:
For holding shell end mills and single angle milling cutters with longitudinal With cutter retaining screw, key and driving ring.
groove in line with DIN 842.
Notes:
Execution: The previous standard DIN 69871-1 was replaced by ISO 7388-1. Required pull
all tapers and tolerances are precision-ground stud no. 23690
concentricity < 0.005 mm If desired with combined shell end mill arbors with ICS, the cutter retaining
with hole for Balluff chip screws must be ordered separately with IC DIN 6367, ref. no. 23185130-180
L1
d1 D
A
Ident. No. 001–015, 061
Ident. No. 050–060, 062–064
p. 754 p. 734
Tool holding device d1 (mm) L1 (mm) A (mm) D (mm) Form 23160...
Ident. No.
SK 40 16 27 55 32 AD 001 ●
SK 40 16 27 100 32 AD 002 ●
SK 40 16 27 160 32 AD 003 ●
SK 40 22 31 55 40 AD 004 ●
SK 40 22 31 100 40 AD 005 ●
SK 40 22 31 160 40 AD 006 ●
SK 40 27 33 55 48 AD 007 ●
SK 40 27 33 100 48 AD 008 ●
SK 40 27 33 160 48 AD 009 ●
SK 40 32 38 60 58 AD 010 ●
SK 40 32 38 100 58 AD 011 ●
SK 40 32 38 160 58 AD 012 ●
SK 40 40 41 60 70 AD 013 ●
SK 40 40 41 100 70 AD 014 ●
SK 40 40 41 160 70 AD 015 ●
SK 50 16 27 55 32 AD 050 ●
SK 50 16 27 100 32 AD 051 ●
SK 50 16 27 160 32 AD 052 ●
SK 50 22 31 55 40 AD 053 ●
SK 50 22 31 100 40 AD 054 ●
SK 50 22 31 160 40 AD 055 ●
SK 50 27 33 55 48 AD 056 ●
SK 50 27 33 100 48 AD 057 ●
SK 50 27 33 160 48 AD 058 ●
SK 50 32 38 55 58 AD 059 ●
SK 50 32 38 100 58 AD 060 ●
SK 50 32 38 160 58 AD 061 ●
SK 50 40 41 55 70 AD 062 ●
SK 50 40 41 100 70 AD 063 ●
SK 50 40 41 160 70 AD 064 ●
Prod. Gr. 2AC
Transverse drive shell end mill arbor (DIN 6357) (DIN 69871-1)
With enlarged collar diameter
SK SK Form G 2,5 ISO
40 50 AD IK 25000 rpm 7388-1
Execution: Internal coolant feed, cooling duct bore cannot be Max. concentricity < 0.005 mm
Alloyed case-hardening steel, tensile strength in closed Delivery:
the core min. 950 N/mm2 Case-hardened HRc 60 ± 2 (HV 700 ± 50), hard- Including Key blocks and cutter retaining screw
ness depth 0.8 mm ± 0.2 mm
A L1
d1D
SK
Ref. no. 23162001-019, SK40 Ref. no. 23162020-034
p. 753 p. 734
Tool d1 (mm) L1 (mm) D (mm) A (mm) 23162... Tool d1 (mm) L1 (mm) D (mm) A (mm) 23162...
holding Ident. No. holding Ident. No.
device device
SK 40 16 17 38 35 001 ● SK 40 22 19 48 35 004 ●
SK 40 16 17 38 100 002 ● SK 40 22 19 48 100 005 ●
SK 40 16 17 38 160 003 ○ SK 40 22 19 48 160 006 ○
Source: Hahn+Kolb Werkzeuge GmbH
Technical data subject to change. www.iconridge.com 711
Availability subject to country specific rules and regulations.
