Page 330 - Industrial Tools Catalog (1)

Milling tools monoblock \ Solid carbide mills for universal machining

Ident. No. 299

Composition of set 6 / 8 / 10 / 6 / 8 / 10 /
12 / 16 mm
12 mm
Number of pieces in 4 5
assortment/set (PCS)
Type N N
16851... Ident. No. 298 299
●
●
Prod. Gr. 150
Solid carbide HPC end mill
4 flutes, ULTRA-coated
Typ Z HB
VHM ULTRA N 4 35°/38° γ = 8° 45° HPC
Application: ƒ Edge-rounded flutes
HPC end mill with uneven twist and uneven pitch for ƒ Centre cutting
universal rough machining and smoothing. ƒ Uneven flute pitch
Execution: ƒ Chip breaker on every flute
ƒ Solid carbide ultra-fine grain Advantage:
ƒ Straight shank in line with DIN 6535 HB ƒ Optimal suitability for trochoidal milling
ƒ ULTRA-coated ƒ With chip breaker geometry for short chips
ƒ With clearance ƒ HPC geometry for highest feed rates and smooth
ƒ Uneven twist angle 35°/38° running
ƒ With edge protection chamfer ƒ Suitable for large cutting depths

Application Steel (N/mm ) 2 Stainless steel Alu Brass Bronze Plas- Graphite GG(G) Titan- Nickel- Super- Hard mat.
No. <700 <1000 <1300 marten. austen. short long short long short long tics G(C)FK GjMW alloy alloy alloy <55 HRC <65 HRC
16851284-294 230 190 150 120 100 350 300 240 280 160 100 70 70
Type N
Surface ULTRA
Tool holding device HB parallel shank
Tolerance of cutting edge Ø e8
Tolerance of shank Ø h6
Z (PCS) fz steel 16851...
1000 ˜ (mm) Ident. No.
mm mm mm mm mm mm mm
6 18 24 62 5.8 6 0.1 4 0.05 284 ●
8 24 30 68 7.7 8 0.2 4 0.06 286 ●
10 31 38 80 9.7 10 0.2 4 0.07 288 ●
12 41 46 93 11.6 12 0.2 4 0.08 290 ●
16 51 58 108 15.5 16 0.2 4 0.11 292 ●
20 61 74 126 19.5 20 0.2 4 0.13 294 ●
Prod. Gr. 150
Solid carbide HPC end mill
4 flutes, TiAlN - coated

Typ Z HB
VHM TiAlN N 4 35°/38° γ = 4° 45° HPC
Application: ƒ With edge protection chamfer
HPC end mill with unequal twist and uneven distribu- ƒ Rounded cutting edge
tion for universal roughing and finishing. ƒ Centre cutting
Execution: ƒ Unequal cutter pitch
ƒ Solid carbide ultra-fine grain Advantage:
ƒ Straight shank pursuant to DIN 6535 HB ƒ Roughing and finishing with just one tool
ƒ TiAlN-coated ƒ Ideally suitable for trochoidal milling
ƒ With clearance ƒ Enables higher feed rates and greater cutting
ƒ Unequal twist angle 35°/38° depths
Application Steel (N/mm ) 2 Stainless steel Alu Brass Bronze Plas- Graphite GG(G) Titan- Nickel- Super- Hard mat.
No. <700 <1000 <1300 marten. austen. short long short long short long tics G(C)FK GjMW alloy alloy alloy <55 HRC <65 HRC
16853201-217 200 160 130 105 85 300 255 205 240 135 85 60 60
16853202-218 200 160 130 105 85 300 255 205 240 135 85 60 60

Source: Hahn+Kolb Werkzeuge GmbH
330 Technical data subject to change. www.iconridge.com
Availability subject to country specific rules and regulations.