Page 377 - Industrial Tools Catalog (1)

Milling tools monoblock \ Solid carbide milling cutter, advanced materials
Solid carbide end mill — fibre glass
4 cutters, diamond-coated

Z HA
VHM
4
Application: Execution: Ident. No. 100–130
This end mill is suitable for the machining of ƒ Solid carbide ultra-fine grain
fibreglass-reinforced plastics, fibreglass, thermo- ƒ Diamond coating
plastics or duroplastic resins, in which fibreglass was ƒ Straight shank in accordance with DIN 6535 HA
introduced as a reinforcement element. The tools are
available with left- and right-hand spiral. Notes: Ident. No. 140–170
You can find detailed information on the usage value
of this tool on our online shop.
Application Steel (N/mm ) Stainless steel Alu Brass Bronze Plas- Graphite GG(G) Titan- Nickel- Super- Hard mat.
2
No. <700 <1000 <1300 marten. austen. short long short long short long tics G(C)FK GjMW alloy alloy alloy <55 HRC <65 HRC
16658100-170 350 200
Type Right-hand twist Left-hand twist
Surface Diamond coating Diamond coating
Tool holding device HA parallel shank HA parallel shank
Tolerance of cutting edge Ø h10 h10
Tolerance of shank Ø h6 h6
Z (PCS) fz alu ˜ (mm) 16658... 16658...
Ident. No. Ident. No.
mm mm mm mm
6 19 76 6 4 0.08 100 ● 140 ●
8 22 76 8 4 0.11 110 ● 150 ●
10 25 76 10 4 0.13 120 ● 160 ●
12 25 76 12 4 0.2 130 ● 170 ●
Prod. Gr. 108
Solid carbide compression milling cutter — fibre glass
4–6 flutes, diamond-coated

Z Z HA
VHM
4 6
Application: Execution:
To prevent delamination when machining fibre ƒ Solid carbide ultra-fine grain
composites and to achieve an optimal edge finish, ƒ Diamond coating
the left-hand spiral generates pressure on the
bottom edge of the workpiece at the bottom of the ƒ Straight shank in accordance with DIN 6535 HA
tool, while the right-hand spiral generates counter ƒ Spiral change as compression zone
pressure on the top of the workpiece at the top Notes:
of the tool. To prevent melting, a greatly positive You can find detailed information on the usage value
cutting angle and deep chipping spaces work against of this tool on our online shop.
over-heating.

2
Application Steel (N/mm ) Stainless steel Alu Brass Bronze Plas- Graphite GG(G) Titan- Nickel- Super- Hard mat.
No. <700 <1000 <1300 marten. austen. short long short long short long tics G(C)FK GjMW alloy alloy alloy <55 HRC <65 HRC
16658200-230 350 200
Surface Diamond coating
Tool holding device HA parallel shank
Tolerance of cutting edge Ø h10
Tolerance of shank Ø h6
Z (PCS) fz alu ˜ (mm) 16658...
Ident. No.
mm mm mm mm mm
6 20 7.75 90 6 4 0.04 200 ●
8 25 8 100 8 4 0.05 210 ●
10 25 8.5 100 10 6 0.065 220 ●
12 25 9 100 12 6 0.08 230 ●
Prod. Gr. 108

Source: Hahn+Kolb Werkzeuge GmbH
Technical data subject to change. www.iconridge.com 377
Availability subject to country specific rules and regulations.