Page 31 - Industrial Tools Catalog (2)

Workpiece clamping \ Vacuum clamping technology
Grid vacuum chuck sets
With venturi nozzle for dry processing

Application: ƒ Good sealing, also suitable for rough (e.g. sawn)
For simple geometric workpieces with rough shapes surfaces
without breakouts or large breakouts that can be ƒ High retention forces, especially suitable for heavy
sealed with sealing cords (size must be a multiple of machining such as milling and grinding
the grid).
Delivery:
Execution: 1 matching vacuum grid plate with a grid pattern of
ƒ With Venturi nozzle 12.5 mm, including built-in compressed air vacuum
ƒ All grid vacuum plates can also be connected to ejector. Mounting grooves and height-adjustable
conventional vacuum pump no. 24501 110 or no. stop discs, 4 x adjustable clamp with a groove
24501 120. width of 14 mm, 1 plastic hose connection for 3 m
ƒ Operating pressure approx. 6 bar quick-release coupling, black vacuum sealing cord
with 4 mm diameter, 10 m, 1 vacuum generator
ƒ Depending on conditions of use, end vacuum up to including silencer and shut-off valve, 1 connection p. 834
92%, air consumption approx. 95 l/min. for conventional vacuum pump.
Advantage: Notes:
ƒ Minor unevenness and curvatures are sealed and Conversion set for wet machining included in scope
compensated for with the elastic sealing cords. of delivery. A vacuum pump is also needed for wet
machining.
Model RV 1 RV 2 RV 3
Vacuum plate length L 300 400 600
(mm)
Vacuum plate height H 32.5 32.5 32.5
(mm)
Vacuum plate width B 200 300 400
(mm)
Grid dimension (mm) 12.5 12.5 12.5
Vacuum panels, can be
linked No No No
24504... Ident. No. 010 020 030
○
○
○
Prod. Gr. 234
Slotted vacuum chuck sets
With venturi nozzle for dry processing
Application: Advantage:
Ideal for light machining tasks such as milling or drill- ƒ High process reliability
ing - e.g. printed circuit boards or electronic compo- ƒ Can be adapted individually to the geometry of
nents - or also engraving. It is thus also possible to the part
securely clamp workpieces that are much smaller ƒ Low-cost entry-level set
than the clamping surface of the vacuum plate.
Workpieces no larger than a postage stamp can ƒ High max. vacuum at approx. 5-6 bar
be cut out of larger material sections using milling ƒ Venturi technology requiring little maintenance
techniques. Individual adaptation to part geometry Delivery:
ensures reliable clamping of almost all conceivable
workpiece geometries. 1 matching vacuum grid plate with a width of 1
mm, distance between centres 5 mm, including
Execution: compressed air vacuum ejector. Mounting grooves
ƒ The narrowing of the cross section within the and height-adjustable stop plates. 4 adjustable p. 834
clamps per slot width = 14 mm, 1 hose connection
Venturi pipe causes a vacuum here, which draws for quick-release coupling and 3 m plastic hose, 1
the air in. suitable brown rubber adapter mat, 1 black rubber
ƒ Distance between slots 5 mm adapter mat, including silencer and shut-off valve, 1
ƒ All slotted vacuum plates can also be connected connection for conventional vacuum pump
also to conventional vacuum pump no. 24501 110
or no. 24501 120. Notes:
ƒ The noise level is just 57 db (A). Conversion set for wet machining included in scope
ƒ Vacuum generation through compressed air of delivery. A vacuum pump is also needed for wet
vacuum ejector: max. vacuum approx. 5-6 bar. End machining.
vacuum of up to 87% depending on conditions of
use. Air consumption approx. 90 l/min.
Model SV 1 SV 2 SV 3
Vacuum plate length L 300 400 600
(mm)
Vacuum plate width B 200 300 400
(mm)
Vacuum plate height H 32.5 32.5 32.5
(mm)
Average slot spacing (mm) 5 5 5
Vacuum panels, can be No No No
linked
24503... Ident. No. 010 020 030
○
○
○
Prod. Gr. 234

Source: Hahn+Kolb Werkzeuge GmbH
Technical data subject to change. www.iconridge.com 831
Availability subject to country specific rules and regulations.