Page 993 - Master Catalog 2017, Inch

Copy Mills • M100 Series
™
Recommended Starting Feeds

„ Recommended Starting Feeds [IPT] Light General Heavy
Machining Purpose Machining

At .197 Axial Depth of Cut (ap)
Programmed Feed per Tooth (fz)
as a % of Radial Depth of Cut (ae)
Insert Insert
Geometry 5% 10% 20% 30% 40–100% Geometry
RDHT-T .009 .015 .026 .007 .011 .018 .005 .008 .014 .004 .007 .012 .004 .007 .011 RDHT-T
RDHW-MH .009 .017 .035 .007 .012 .025 .005 .009 .019 .004 .008 .016 .004 .007 .015 RDHW-MH
RDMT-T .009 .015 .026 .007 .011 .018 .005 .008 .014 .004 .007 .012 .004 .007 .011 RDMT-T
RDMW- .009 .008 .024 .007 .006 .017 .005 .004 .013 .004 .004 .011 .004 .004 .010 RDMW-
RDMW-T .009 .022 .035 .007 .016 .025 .005 .012 .019 .004 .011 .016 .004 .010 .015 RDMW-T

At .098 Axial Depth of Cut (ap)
Programmed Feed per Tooth (fz)
as a % of Radial Depth of Cut (ae)
Insert Insert Copy Mills
Geometry 5% 10% 20% 30% 40–100% Geometry
RDHT-T .010 .018 .030 .008 .013 .021 .006 .010 .016 .005 .008 .014 .005 .008 .013 RDHT-T
RDHW-MH .010 .019 .040 .008 .014 .029 .006 .010 .021 .005 .009 .019 .005 .008 .017 RDHW-MH
RDMT-T .010 .018 .030 .008 .013 .021 .006 .010 .016 .005 .008 .014 .005 .008 .013 RDMT-T
RDMW- .010 .009 .027 .008 .007 .020 .006 .005 .015 .005 .004 .013 .005 .004 .012 RDMW-
RDMW-T .010 .026 .040 .008 .019 .029 .006 .014 .021 .005 .012 .019 .005 .011 .017 RDMW-T

At .049 Axial Depth of Cut (ap)

Programmed Feed per Tooth (fz)
as a % of Radial Depth of Cut (ae)
Insert Insert
Geometry 5% 10% 20% 30% 40–100% Geometry
RDHT-T .014 .023 .039 .010 .017 .028 .007 .012 .021 .006 .011 .018 .006 .010 .017 RDHT-T
RDHW-MH .014 .025 .053 .010 .018 .038 .007 .014 .028 .006 .012 .025 .006 .011 .022 RDHW-MH
RDMT-T .014 .023 .039 .010 .017 .028 .007 .012 .021 .006 .011 .018 .006 .010 .017 RDMT-T
RDMW- .014 .012 .036 .010 .009 .026 .007 .007 .019 .006 .006 .017 .006 .005 .015 RDMW-
RDMW-T .014 .034 .053 .010 .024 .038 .007 .018 .028 .006 .016 .025 .006 .015 .022 RDMW-T

At .025 Axial Depth of Cut (ap)
Programmed Feed per Tooth (fz)
as a % of Radial Depth of Cut (ae)
Insert Insert
Geometry 5% 10% 20% 30% 40–100% Geometry
RDHT-T .019 .032 .053 .014 .023 .038 .010 .017 .028 .009 .015 .025 .008 .014 .023 RDHT-T
RDHW-MH .019 .034 .073 .014 .025 .052 .010 .019 .039 .009 .016 .034 .008 .015 .031 RDHW-MH
RDMT-T .019 .032 .053 .014 .023 .038 .010 .017 .028 .009 .015 .025 .008 .014 .023 RDMT-T
RDMW- .019 .017 .049 .014 .012 .035 .010 .009 .026 .009 .008 .023 .008 .007 .021 RDMW-
RDMW-T .019 .047 .073 .014 .033 .052 .010 .025 .039 .009 .022 .034 .008 .020 .031 RDMW-T
NOTE: Use “Light Machining” value as starting feed rate.

widia.com K85

10/29/15 1:43 PM
WID_Master16_IndexableMIlling_CopyMills_K084_K085_Minch_REBRAND.indd 85 L V i WID M 16 I d bl MIlli C Mill K084 K085 Mi h REBRANDO b 1420151149AM