Page 335 - Modernfold Architectural Products

Modernfold Compactline Technical Data
®
10 22 26 Operable Partitions

MOVABLE GLASS WALL TECHNICAL DATA

2.5 PANEL FINISHES PART 3 EXECUTION
A. Provide top and bottom rails with one of the
following finishes: 3.1 INSTALLATION
1. Clear satin anodized aluminum A. General: Comply with ASTM E557, operable
2. Satin stainless steel anodized aluminum glass partition manufacturer’s written installation
3. White Powder Coat (RAL 9016) instructions, Drawings, and approved Shop
4. Black Powder Coat (RAL 9004) Drawings.
5. RAL “Classic” (Solids collection) Powder Coat B. Install operable glass partitions and accessories
available (Sherwin Williams’ Powdura Super after other finishing operations, including painting,
Durable TGIC Free Polyesters) provided in one have been completed.
of the following (select one): C. Match operable glass partitions by installing
a. Gloss finish (80°-85° gloss) panels from marked packages in numbered
b. Satin finish (30° gloss) sequence indicated on Shop Drawings.
D. Broken, cracked, chipped, deformed, or
2.6 SUSPENSION SYSTEM unmatched panels are not acceptable.
A. G-330 Suspension System 3.2 CLEANING AND PROTECTION
1. Suspension Tracks: Extruded aluminum with a A. Clean metal and glass surfaces upon completing
minimum wall thickness of 0.235 inches installation of operable glass partitions to
(6 mm). Incorporate cast aluminum or mitered remove dust, loose fibers, fingerprints, adhesives,
intersections, switches, and curves in stacking and other foreign materials according to
area. Provide alignment pins for track, manufacturer’s written instructions.
intersections, switches and curves insuring both B. Provide final protection and maintain conditions
fit and roller surface integrity. in a manner acceptable to manufacturer and
a. Exposed track soffit: Factory-finished Installer that insure operable glass partitions
aluminum with white powder coat. are without damage or deterioration at time of
2. Carriers: Two stainless steel trolleys with vinyl Substantial Completion.
roller surfaces. Trolley design incorporates eight
(8) wheels of varying dimensions. Automatic 3.3 ADJUSTING
indexing of panels into stack area is provided A. Adjust operable glass partition to operate
by pre-programmed switches and trolleys smoothly, easily, and quietly, free from
without electrical, pneumatic, or mechanical binding, warp, excessive deflection, distortion,
activation. nonalignment, misplacement, disruption, or
malfunction, throughout entire operational range.
2.7 OPTIONS Lubricate hardware and other moving parts.
A. Pass Doors
1. Sliding Swing Door: Top hung operating swing
door, rails heights to match partition rails 3.4 EXAMINATION
providing uniform appearance. A. Examine flooring, structural support, and
2. Hardware opening, with Installer present, for compliance
a. Automatic door closer with requirements for installation tolerances
i. Floor closer and other conditions affecting performance of
ii. Overhead closer operable glass partitions. Proceed with installation
b. Push/Pull Bars only after unsatisfactory conditions have been
c. Mortise Cylinder Floor Locks corrected.
B. Door pulls back-to-back 1. Insure finished floor under operable glass
1. 12” tubular pull partition is level ± 0.13-inch (3 mm) in ten (10)
2. Manet 1240mm “Ladder Pull” feet (3048 mm) non-cumulative.
3. TG-138 49” locking “Ladder Pull”
C. Automatic door closer – Pivot Panel 3.5 DEMONSTRATION
1. BTS80 floor closer A. Demonstrate proper operation and maintenance
D. Intersecting partition interface procedures to Owner’s representative.
1. 90° corner post B. Provide Operation and Maintenance Manual to
2. 95°-175° corner post Owner’s representatives.

Please contact your local Modernfold distributor for further assistance, or visit our website at www.modernfold.com. 3