Page 40 - Arch binder

Operable Partitions PART 2 - MODEL 3010 PRODUCT SPECIFICATION
10 22 26 (10650)

2.01 ACCEPTABLE MANUFACTURER 2.04 STACK ARRANGEMENTS
A. Operable walls shall be Series 3000, Model 3010 Individual A. Stack Type: Panel storage confi guration shall be (select):
Panels / Curve & Diverter as manufactured by
KWIK-WALL Company. 1. Standard Perpendicular Stack: consisting of panels stacking
o
at a 70 angle perpendicular to the wall’s installed position.
2.02 PANEL CONSTRUCTION 2. Optional Parallel Stack: consisting of panels stacking at a 20 o
angle parallel to the wall's installed position. (Note: For panel
A. Panel Dimensions: Standard panel dimension shall be a nominal o
4" [101.6] thick. fabrication heights over 16'-2" (4.93 m) panels stack at a 20
B. Panel Frame: Steel frame shall be 16-gauge galvanneal steel, angle parallel to the wall’s installed position.)
horizontal top cross member shall be minimum 12-gauge 3. Optional Remote Stack: consisting of panels stacking at a 20 o
galvanneal steel which meets or exceeds ASTM A 653 angle located remotely from the wall's installed position, as
requirements. Frame shall be all-welded construction with steel shown on submitted shop drawings. (Note: For panel fabrication
o
corner supports and crossbracing reinforcement. Panel frame shall heights over 16'-2" (4.93 m) panels stack at a 20 angle remotely
be Class A rated, fi re retardant, non-combustible and non-corrosive from the wall’s installed position.)
in accordance with ASTM E 84.
B. Stack Quantity: Panels shall be stored in separate stack areas as
required for panel storage.
C. Panel Skins: Panel skins shall be Class A rated (except Wood
Veneer and High Pressure Laminate) in accordance with ASTM E 2.05 FINISHES
84. Panel skin material shall consist of (select):
A. Finish Material Type: Panel fi nish material shall be Class A
1. Standard Steel Skins: consisting of minimum 22-gauge
tension leveled galvanneal steel, pressure laminated to a (except wood veneer and high pressure laminate) rated in
structural acoustical backer and mechanically fastened to the accordance with ASTM E 84, consisting of (select):
steel frame to form a rigid, unitized and structural panel. 1. Standard Vinyl: consisting of Type II, reinforced vinyl weighing
21 oz./lin. yd. (651 g/lin. m). Vinyl shall meet or exceed
2. Optional Acoustical Substrate: consisting of structural
acoustical substrate pressure laminated to both sides of the CCC-W-408A and CFFA-W-101-D quality standards.
steel frame to form a rigid, unitized and structural panel. 2. Optional Upgrade Fabric: consisting of fade and tear resistant
fabric that resists water-based stains weighing 13 oz./lin. yd.
3. Optional Wood Veneer: consisting of particle board core covered (403 g/lin. m).
with wood veneer and pressure laminated to both sides of the 3. Optional Basics Carpet: consisting of acoustically absorbent,
steel frame to form a rigid, unitized and structural panel. non-woven needle punch fi bers fused to prevent fraying and
unraveling of material weighing 28.5 oz./lin. yd. (884 g/lin. m).
4. Optional High Pressure Laminate: consisting of particle board Basics Carpet shall achieve a minimum NRC (Noise Reduction
core covered with general purpose plastic laminate and Coeffi cient) rating of .20 (applied over gypsum substrate)
Phenolic backer sheet, which is pressure laminated to both sides accordance with ASTM C 423.
of the steel frame to form a rigid, unitized and structural panel.
4.Optional Upgrade Carpet: consisting of acoustically absorbent,
D. Panel Hinges: Panel hinges (if required): shall be architectural non-woven needle punch fi bers fused to prevent fraying and
grade, full leaf butt hinges. Hinges shall be attached to steel frame unraveling of material weighing 23 oz. / lin. yd. (713 g / lin.
utilizing a steel mounting bracket welded to frame. m). Upgrade Carpet shall achieve a minimum NRC (Noise
Reduction Coeffi cient) rating of .25 (applied over gypsum
E. Panel Weight: Maximum panel weight shall be 5.9 – 12.9 lb./ft. 2
2
(29 – 63 kg/m ) depending on STC rating, size and options substrate) in accordance with ASTM C 423.
selected. 5. Optional Wood Veneer: consisting of unfi nished fl at cut wood
veneer laminated to 1/2" [12.7] thick particle board core.
2.03 OPERATION Veneer shall be book / running matched within a panel, and
A. Operation shall be Individual Panels / Curve & Diverter, consisting vertically edge banded if Trimless astragals are specifi ed.
of Individual Panels that are top supported by two (2) carriers (Notes: Optional Class "A" rated particle board is available. Acoustical
riding through radius Curve and Diverter type intersections. substrate STC ratings apply for Wood Veneer panel construction..)
MODEL 3010 PRODUCT GUIDE
MODEL 3010 PRODUCT GUIDE
Standard Steel Skin Construction Optional Acoustical Substrate Construction
STC Panel Thickness Max. Panel Maximum Maximum
STC Panel Thickness Max. Panel Maximum Maximum Rating (nominal) Weight lb./ft. 2 Panel Height Wall Width
Rating (nominal) Weight lb./ft. 2 Panel Height Wall Width
2
46 4" [101.6] 8.5 (41 kg/m ) 24' - 2" (7.37 m) Unlimited 43 4" [101.6] 5.9 (29 kg/m ) 16' - 2" (4.93 m) Unlimited
2
2
50 4" [101.6] 9.5 (46 kg/m ) 24' - 2" (7.37 m) Unlimited 46 4" [101.6] 6.6 (32 kg/m ) 16' - 2" (4.93 m) Unlimited
2
2
52 4" [101.6] 9.5 (46 kg/m ) 24' - 2" (7.37 m) Unlimited 48 4" [101.6] 7.5 (37 kg/m ) 16' - 2" (4.93 m) Unlimited
2
2
56 4" [101.6] 12.9 (63 kg/m ) 24' - 2" (7.37 m) Unlimited 50 4" [101.6] 9.0 (44 kg/m ) 16' - 2" (4.93 m) Unlimited
2
*Optional Wood Veneer or High Pressure Laminate only available as
* Estimated panel weights are for intermediate panels. Weight may vary due to
substrate, size, or function of panel. Add 105 lbs [47kg] for pass door. Add 6 lbs [3kg] per Accoustical Substrate Construction.
lin ft height for expanders. Add 3.5 to 8 lbs [1.6 to 3.6kg] per lin ft for track. *** Horizontal Splice: Heights over 14'2" [4.31] with Acoustical Substrate
**Standard features can be modifi ed, contact your Kwik-Wall distributor for the features require a structural splice. 3
you want.
Dimensions in [ ] are millimeters. Contact your local distributor for additional assistance or visit www.kwik-wall.com 04-18
07-15