Page 7 - Section A - Complete

Flywheel Tools

Flywheel Pullers
Used for the removal of the Flywheel or rotor if applicable. Premium quality high carbon steel and heat treated for strength and durability.
For our full range of pullers, please see our Full Tools Catalogue.

00-104/102 00-101 00-097 00-126 00-236 00-231 00-407 00-863 00-864 00-376 00-085

Flywheel Extractors with thread on Outside of Extractor Flywheel Extractors with thread on Inside of Extractor Flywheel Extractors Stud Type
Size (mm) Thread Part No. Size (mm) Thread Part No. Size (mm) Thread Part No.
26 x 1.50 & Right Hand 00-104/102 24 x 1.50 Right Hand 00-236 20 x 1.50 Right Hand 00-085
27 x 1.25 26 x 1.00 Right Hand 00-231
27 x 1.00 Left Hand 00-101 28 x 1.00 Right Hand 00-407
27 x 1.00 Right Hand 00-097 28 x 1.00 Right Hand 00-863
30 x 1.50 Right Hand 00-126 33 x 1.50 Right Hand 00-864
35 x 1.50 Right Hand 00-376

Univ. Rotor Puller 6 Sizes
Flywheel Puller / Primary Gear Extractor
A specially designed tool for standard AC flywheel
Designed to remove the rotar and primary gear on rings. Features 6 different sizes: M27x1.0L, M24x1.0R,
a KTM50 02-07. Comes with 4mm, 5mm and 6mm M18x1.5R, M16x1.5R, M14x1.5R and M10x.125R.
hardware. Replaces OEM tool 59029021044.
Part No. 00-088
Flywheel Puller 00-312 Trade PK of 5 00-088.PK5

Clutch/Flywheel Holding Tool

Pilot Bearing Puller
Bridge type - Pilot bearing puller. A very slim line 3 jawed
design internal puller for removal of most flywheel pilot
bearings. Work travel: 13-38mm.
Designed to hold clutch baskets, flywheels, gears, sprockets
Pilot Bearing Puller 00-437 etc. Jaws open to 5” wide. Made of medium carbon steel with
hardened jaws. A very usefull workshop tool for holding any
kind of mechanical work.
Clutch/Flywheel Tool 00-890
Trade Pack of 10 00-890.DR.PK/10

Cr Seal/Bearing Retainer Tool (Ktm)
22mm hex and 3/8 square drive. Precision design prevents
damage to the retainer ring after peened “stakes” have been
47Mm Cr Seal Bearing Retainer Tool removed by drilling. Replaces the OEM Honda tool to remove
and replace the rear wheel bearing/seal retainer ring, OEM
Versatile design features a 22mm hex and 3/8 square drive. REF: 41231-430-000. For use on: CR250R 1978-81.
Precision design prevents damage to the retainer ring after
peeded “stakes” have been removed by drilling. 47mm CR Seal/Bearing Retainer Tool 00-214
repaces OEM tools 07HMA-KS70100 AND 07YMA-KZ40100 to
remove and replace the rear wheel bearing/seal retainer rings.
CR125/250 87-88, 00-02, CR500 87-88.
47mm Retainer Tool 00-213

*Please See Our Tools Catalogue For Full Range Of Products
E-mail: oro@btconnect.com www.oro2u.com A5