Page 215 - 2019 Allstar Performance Parts and Equipment Catalog

Cleco Pin Fastener Kits Quick Turn Spring Fixture
Cleco pins are reusable and easily NEW! Accurately drill panels when installing
make a temporary connec- quick turn fastener springs. Start with ALL19407
tion between pieces of a 1/4" center hole and use the fixture
sheet metal during fit- to locate and drill 1/8" holes for mounting
ting. Pins will work with the springs. Size listed is spring center-to-center
thicknesses up to 1/4", kits distance. TOOLS & PIT EQUIPMENT
include pliers and 10 pins. ALL19406 ..... Fixture For 3/4" Spring
ALL18221 ..... Kit With 1/8" Pins ALL19407 ..... Fixture For 1" Spring
ALL18225 ..... Kit With 3/16" Pins ALL19408 ..... Fixture For 1-3/8" Spring
Spindle Checker Tools
Cleco Pliers ALL18220
Assure correct alignment of the
Unique tool readily
installs and removes upper and lower ball joint
Cleco fasteners. when checking for bent
spindles. Insert slugs
into spindle and
Pin Type Cleco Fasteners
guide rod will fit
Cleco pins permit quick, easy installation through slugs if spindle isn’t bent. Kits fit most
and removal of sheet metal during fitting. aftermarket race and GM stock Metric spindles.
Pins work with thicknesses up to 1/4".
ALL11176 ...... Kit With GM Lower, 2" Taper
1/8" Dia. Pins 3/16" Dia. Pins ALL11177 ...... Kit With Chrysler Lower, 1-1/2" Taper
ALL18222 ..... 10-Pack ALL18226 ...... 10-Pack ALL11184 ...... Kit For GM Metric, 2" Taper
ALL18223 ..... 25-Pack ALL18227 ...... 25-Pack Related Parts
ALL18224 ..... 100-Pack ALL18228 ...... 100-Pack ALL99140 ..... GM Lower Slug With Nut (2" Per Ft.)
ALL99141 ..... Chrysler Lower Slug With Nut (1-1/2" Per Ft.)
TECH TIP ALL99158 ..... GM Metric Lower Slug With Nut (2" Per Ft.)
Drill holes one drill size smaller than the Cleco pin size to ALL99142 ..... Upper Slug With Nut (1-1/2" Per Ft.)
assure a tight fit. ALL99159 ..... GM Metric Upper Slug With Nut (2" Per Ft.)
ALL99143 ..... Replacement Guide Rod
Clamp Type Cleco Fastener Taper Reamers
ALL18230 Repair or enlarge tapered holes to accept tie rod
Use when drilling is not an option. Smooth throat ends or ball joints. Reamers may be used in a
prevents paint damage, and spring exerts strong drill with a 1/2" chuck by removing the T-handle.
clamping pressure. Throat depth is 1" with a maximum ALL11170 ...... Reamer, 7.15°, 1-1/2" Taper Per Ft.
clamping range of 1/2". ALL11172 ...... Reamer, 9.56°, 2" Taper Per Ft.

Quick Turn Fastener Wrench Taper Reamer Specifications For Ball Joints
ALL19400 Part No. Taper Specs Part No. Taper Specs
The Allstar quick turn fastener Ball Joint Ball Joint
wrench fits slot head fasteners and ALL56204 1-1/2" Per Ft. ALL56217 1-1/2" Per Ft.
reduces the risk of body panel or fastener damage when ALL56206 2" Per Ft. ALL56218 2" Per Ft.
using screwdrivers for loosening or tightening. Features a ALL56208 2" Per Ft. ALL56220 2" Per Ft.
non-slip handle. ALL56210 1-1/2" Per Ft. ALL56280 1-1/2" Per Ft.
ALL56212 2" Per Ft. ALL56284 1-1/2" Per Ft.
ALL56214 1-1/2" Per Ft. ALL56286 1-1/2" Per Ft.
Quick Turn Spring Adjuster ALL56216 1-1/2" Per Ft. – –
ALL19405
Ball Joint Spreader Tool ALL11174
This tool is a must when adjusting tension
of quick turn springs. Simply turn knob on adjuster to evenly Tool separates ball joint from the spindle. Inside of
pull or push spring without kinking or breaking spring. cylinder is shaped to fit over tapered stud of most
ball joints and presses against stud of other ball
joint. Not for use on FWD or 4WD applications. Tool
Transfer Punches is 4" tall fully collapsed and 6" tall fully extended.
Used to mark quick turn fastener locations, place
transfer punch in the initial hole in weld plate or Related Part
body panel. Position the panel to be marked over ALL11175 ...... 1" Extensions (Set of two)
top of punch and lightly tap with a hammer. ALL11175
ALL19402 ..... For 5/16" Fasteners
ALL19403 ..... For 7/16" Fasteners
www.allstarperformance.com 213