Page 48 - 2017 Racecar Engineering Circle Track Parts and Accessories Catalog

ENGINE

SWIVEL EXHAUST HANGER ALL34220 MOTOR PLATES
Hanger swivels horizontally and vertically to simplify mounting in any Motor plates are used
position. Bolt or weld to chassis to support additional weight of mufflers, to replace the front motor
turndowns, etc. Steel strapping is 1/8" thick. mounts allowing relocation
of the engine in the chassis,
HEADER WRAP including lowering or when
Reduce underhood temperature while containing header tube heat for moving the engine back in the chassis. Plates prevent engine movement and
reinforce the front suspension for better handling and increased reaction times.
increased power. Fiberglass woven wrap is available in natural or black rolls. Fabricated from 1/4" thick 6061-T6 aluminum, motor plates are often trimmed
Part No. Description to fit the chassis or frame mounts. Plates are machined for a perfect fit to
1" Wide Rolls mount between the water pump and engine block.
ALL34240 Natural 15' Part No. Description
ALL34241 Natural 25' ALL38120 SB Chevy 10" x 36"
ALL34242 Natural 50' ALL38124 BB Chevy 12" x 36"
ALL34243 Natural 100'
ALL34250 Black 15' BELLHOUSING DOWEL PINS
ALL34251 Black 25' Steel dowel pins are approximately 1/2" longer
ALL34252 Black 50' than stock pins and are required when running
ALL34253 Black 100' an engine mid-plate, rear motor mounts or an
2" Wide Rolls aftermarket bellhousing. These extended length pins also
ALL34244 Natural 15' help with alignment when installing an engine. Pins fit most ALL38152
ALL34245 Natural 25' GM blocks and are sold in pairs.
ALL34246 Natural 50' Part No. Description
ALL34247 Natural 100' ALL38150 Solid Pins
ALL34254 Black 15' ALL38152 Hollow Pins
ALL34255 Black 25'
ALL34256 Black 50' ENGINE MID-PLATES
ALL34257 Black 100' Aluminum mid-plates are 1/4" thick 6061 aluminum, black powder coated
and profiled to keep weight at a minimum (less than 4 pounds) without compro-
STAINLESS STEEL CABLE TIES mising strength or durability. Unique, dual mounting holes (unless specified
otherwise) allow engine to be raised 1" in chassis.
Part No. Description
ALL34262 7-1/2" Long, Package of 8
ALL34264 14-1/2" Long, Package of 4

EXHAUST SHIELDS
Aluminum shields protect body panels from exhaust exiting thru the passen-
ger door and provide a clean, finished look from the outside simplifying exhaust ALL38132
routing. Round shield I.D. is 6", commonly used for exiting one 5" diameter
exhaust pipe. Oval shield I.D. is 5" x 9", commonly used for exiting two 3-1/2" Part No. Description
diameter exhaust pipes. ALL38131* SB Chevy, 5/8",
Dirt Works/Pierce/Bandit Chassis, 3.1 lbs.
SB Chevy, 5/8",
ALL38132
Dirt Works/Pierce/Bandit Chassis, 3.6 lbs.
SB Ford, 5/8",
ALL38133
Dirt Works/Pierce/Bandit Chassis, 3.6 lbs.
ALL34180 ALL34181 ALL34182 ALL34183 ALL38134 SB Chevy, 1-1/8",
Part No. Description Pierce LM, Barry Wright Chassis, 3.9 Lbs.
ALL34180 Round Flange, 55 Degrees To Door ALL38135 SB Chevy, 1-1/2",
ALL34181 Round Flange, 90 Degrees To Door Mastersbilt Chassis, 3.5 lbs.
ALL34182 Oval Flange, 55 Degrees To Door ALL38136 SB Chevy, 2", Rayburn Chassis, 3.7 lbs.
ALL34183 Oval Flange, 90 Degrees To Door ALL38138 SB Chevy/SB Ford,
2-5/8", Rocket Chassis, 3.4 lbs.
ALL38139
CRANKCASE EVACUATION SYSTEM * Only one set of mounting holes SB Chevy / SB Ford Shaw, 2.8 lbs.
ALL34145
Reduce crankcase pressure for optimum
piston ring seal, fewer oil leaks and ALUMINUM MOTOR MOUNT
better engine performance. System ALL38098
includes two of each: chrome plated Small block Chevy aluminum front motor mount is cen-
push-in breathers, check valves, weld- tered for standard positioning. 1/4" thick, sold each.
in 3.5" long threaded pipe adapters,
rubber breather grommets and four
hose clamps. Evacuation hoses not included. Use
with 5/8" diameter hose.

47