Page 147 - 2020 Allstar Performance Parts and Equipment Catalog

Ford 9" Floater Housings Custom Ford 9" Housings

Housings are jig welded for correct alignment using a Custom Ford 9" housings can be built to any width and REAR ENDS & AXLES
select used center section, new 3" O.D. x 3/16" wall axle pinion location with floating axle style pins or standard
tubes and include gear case mounting studs, fill and drain flanged axle ends. Floating axle style housings are avail-
plugs. Note: Axles are sold separately. able with most 5x5 or Wide 5 hub pins. Standard flanged
axle housings can be ordered with Small Ford, Early Big
Housing Width/Offset 2.0" Pin 2.5" Pin Ford or Late/Torino Big Ford ends. All housings feature
58"/Centered – ALL68820 select used center sections, new 3" O.D. x 3/16" wall axle
60"/Centered ALL68700 ALL68822 tubes installed and completely jig-welded for straightness.
60"/2" Offset ALL68702 – To order please call and request a special-order form then
61"/Centered ALL68703 –
62"/Centered ALL68704 ALL68824 fill in all required information and return to us with a sig-
62"/2" Offset ALL68706 – nature attached. Housings are non-returnable and offered
63"/2" Offset ALL68708 – on a special-order basis only.
64"/Centered ALL68709 – ALL68710 ..... Custom Housing Bare
ALL68711 ..... Custom Housing w/GM Metric Mounts NEW!
TECH TIP
Housing Measuring Diagram Rear End Station Brackets ALL10178
Stand adapter
(60"*)
brackets fasten to
adjustable arms of
(28"*) (32"*) most engine stands.
Supports full size
car and light truck
Top Viewp V
To
Front Of Vehicle
Front rear axle housings Engine Stand Not Included
when servicing or
replacing differential gear sets. Position housing onto
arms and secure into place with included retaining straps.
(Engine stand sold separately).
Example: Bare housing ALL68702 is 60" from hub face
to hub face and the pinion is located 2" to the left of the
housing centerline when viewed from rear of housing.*
Pinion Centering Jig ALL68370
Notes: Please measure and inspect housing before welding brackets or painting.
Housing is non-returnable if modified or custom. Welding suspension brackets Pinion centering jig fastens to the rear end housing
on rear end housings can cause warping. Check for straightness after welding. and locates the pinion centerline when building or
These housings use Allstar ALL72100 inner grease seals.
narrowing housings. Machined slots are designed
*Dimensions for example only.
to retain most tape measure ends for accurate
measurements. Applications include GM 12 and
Hot Rod Ford 9" Housings 14-Bolt, Dana 44 and 60, Chrysler 8-3/4", and
Ford 8.8" and 9" housings.

Ford 9" Truss Support ALL68330
Steel Hot Rod housings are built with all Weld-on support
new components. The pumpkin section adds strength to
is centered, so the pinion yoke is offset rear axle housing
approximately 1" to the right allowing and reduces
for symmetric tube bracketry on each side. Includes vent, unwanted flex
pumpkin studs and bearing retainer t-bolts. Tube diam- during extreme torque. Constructed of 12 gauge (.108")
eter is 3" with 3/16" wall thickness and features large steel. 36" L x 2" W.
bearing late/Torino style ends. Axles sold separately.
Width measurements are from axle flange to axle flange.
ALL68830 ..... 56"
ALL68832 ..... 58"
ALL68834 ..... 60"

www.allstarperformance.com 145