Page 228 - 2020 Allstar Performance Parts and Equipment Catalog

TOOLS & PIT EQUIPMENT

Engine Lift Plate ALL10123 Freeze Plug Driver Set ALL96482
Ease engine swaps with the Allstar Have problems installing freeze plugs? Use these plastic
engine lift plate. Bolts to manifold in drivers along with a hammer or mallet for simple instal-
place of carburetor. Yellow zinc coated lation without damaging
plate fits standard Holley 4150/4160 and the plugs or the block.
4500 Dominator, Rochester Quadrajet, Carter, Motorcraft, Three sizes per set: 1-1/2",
Edelbrock, Edelbrock Q-Jet and Carter AFB carburetors. 1-5/8", 1-3/4".
(Size refers to size of plug)
All-In-One Engine Lift Plate ALL10137 Individual Drivers
Engine Plate has provi- NEW! ALL96483 .... 1-1/2" Driver
sions to fit all LS GM ALL96484 .... 1-5/8" Driver
engine blocks and most Holley ALL96485 .... 1-3/4" Driver
4150/4160 and 4500 series,
Rochester Quadrajet, Edelbrock and Cam Bearing Installation Tool ALL96470
Carter AFB Carburetors. Plate features
three lifting points for various chain positioning
which allows engine weight to be balanced or offset.
An offset position is especially helpful when angling an For installing cam bearings quickly and easily without
engine (with transmission attached) in or out of a vehicle. damage. Shaft is steel; pilot and driver are aluminum.
Constructed of 3/16" thick zinc plated steel.
LS Main Cap
Engine Lift Plates For Removal Tool
LS Series GM Engines ALL96525
Engine plates are designed for lifting Quickly and easily pull main
LS series GM engines. Installation of lift bearing caps off GM LS series V8
plate requires removal of the intake mani- engines, especially those with main studs. Hook tool to
fold and valley cover tray to properly secure lift the bottom of cap, press down on handles, and the bal-
plate to engine block. Plate features three lifting ALL10140 anced leverage pulls the cap out of the block with one
points, allowing engine weight to be balanced or offset. swift motion. 26" long x 4" high.
Made from 3/16" thick zinc plated steel.
ALL10140 ..... LS Gen III Engine Lift Plate Rod And Piston Holder ALL96478
ALL10143 ...... LS Gen IV Engine Lift Plate
ALL10141 ...... LS Gen V Engines Holder safely supports piston
and connecting rod assem-
Ford EFI Engine blies during engine teardowns
or assembly. Slots are 4-3/4" L
Lift Plate ALL10125 x 1-1/2" W to accommodate
Ease engine swaps with the Allstar most combinations. Holder mea-
engine lift plate. Fits standard 5.0L/5.8L EFI sures 24" x 12" x 9-1/2" tall and can be
intakes: OEM, GT-40, Cobra, Holley, Edelbrock. disassembled for storage.

Engine Oil Pressure Rod Guide Tool ALL96480
Primer Tank ALL10535 Plastic tool slips over 3/8"
Primer tank supplies initial oil or 7/16" rod bolts to aid
to the oil pump in engines piston installation and elimi-
equipped with a crank driven nate the chance of rod bolts
oil pump. Fill primer tank with hitting crank. A must for
engine oil, then apply compressed any engine builder’s toolbox.
air to force the fluid throughout the Related Part
engine via the oil pressure sender/switch port to pre-lube ALL96481 ..... Rod Guide Tool Extensions 4.5", 1-Pair
the entire engine including the oil pump.
®
Plastigage Kit ALL96475
Oil Filter Cutter Plastigage strings are a simple and accu-
ALL10538 rate way to verify crankshaft, main
Tool removes the outer shell and rod bearing clearances. Kit
of most spin-on style engine includes two green .001" to
oil filters to inspect the filter .003" and one red .002" to .006"
material for contamination (12" long strings), individually packaged inside calibrated
or debris. sleeves. Detailed instructions are included.
226 www.allstarperformance.com