Page 255 - 2020 Allstar Performance Parts and Equipment Catalog

Torque Ball Safety Blanket ALL55220 Bert Clutch Assembly Tool
Fire resistant safety blanket designed by ALL14295
Jason Meyers Racing protects drivers’ Shaft is used to help align
legs and feet in the event of a U-joint counter shaft when replacing
failure. Ballistic nylon covered blanket clutch discs and clutches. Shaft features a
weighs just 1-1/2 lbs. and has quick through hole for installing threaded rod
release adjustable straps that allow when assembling counter gear assembly before instal-
blanket to be removed easily for lation, along with an internal thread to assist when
servicing torque ball and U-joint. Blanket removing if necessary. TRANSMISSION COMPONENTS
includes two mounting brackets, mounting studs, nuts and
installation instructions.
Tailshaft Seal And Bushing
Replacement Parts The tailshaft bushing is a regular wear
ALL55224 ..... 3/8" Mounting Stud Kit item, located inside the transmission tailshaft
ALL55226 ..... Mounting Tabs, 1-Pair
housing. It should be replaced when replacing ALL72152
the tailshaft seal or when a driveshaft failure has
occurred. A worn bushing will cause excessive side-to-side
Bellhousing Dowel Pins movement of the slip yoke and create a vibration or leak.
Steel dowel pins are approximately 1/2" Replacement bushing and seal fits GM Powerglide, Turbo
longer than stock pins and are required when ALL38152 350, Saginaw, Muncie, Bert and Brinn transmissions.
running an engine mid-plate, rear motor mounts or an ALL72150 .... Seal
aftermarket bellhousing. These extended length pins also ALL72152 .... Seal With Bushing
help with alignment when installing an engine. Pins fit
most GM blocks and are sold in pairs. Slip Yokes
ALL38150 ..... Solid Pins Slip yokes provide an important link in today’s driveline
ALL38152 ..... Hollow Pins and chassis combinations. Yokes are available in standard
length for most street applications with minimal suspen-
sion travel to extra-long for racing suspensions that have a
radical amount of travel. 27-spline yokes accept 1310 style
Solid Transmission Mount
U-joints and are for use in many popular transmissions
ALL38070 including TH350, TH700R4, Muncie and
Solid 3/16" steel mount fits most TH350, Saginaw 3 and 4 speeds, Bert and Brinn
TH400, Powerglide, and all BorgWarner, Muncie, and non-ball spline.
Chrysler 4-speed transmissions. Eliminates twisting, flex, ALL69040 ..... 6"
and distortion. Not recommended for use with rubber ALL69042 ..... 6-3/4"
engine mounts. ALL69044..... 7-1/2" 6-3/4"
ALL69046 ..... 8"
ALL69048 ..... 8" (Extra Clearance) 4-3/4"
Transmission Mount Bracket Hardened
ALL69043 ..... 6-3/4"
ALL38072 ALL69045 ..... 7-1/2"
ALL69042
May be welded to chassis to support ALL69047 ..... 8" ALL69043
manual or automatic transmissions. Steel
bracket is 1/8" thick with 1" x 7/16" slots for U-Joints
mounting bolts. Performance U-joints are greasable
and fit a variety of driveshaft
combinations.
Clutch Discs 1310 Series: 3.218" Wide with 1.062" Diameter Caps
1330 Series: 3.622" Wide with 1.062" Diameter Caps
For Bert Transmission 1350 Series: 3.622" Wide with 1.187" Diameter Caps
Quality discs are a must when rebuilding
the internal clutch of Bert transmissions. U-Joints With Same Cross Width
Friction disc and steel plate sets are sold ALL69030 ..... 1310 Series
separately. ALL69031 ..... 1330 Series
ALL69032 ..... 1350 Series
Note: Friction discs need to be soaked in U-Joints With Different Cross Widths
Type-F automatic transmission fluid for at least 2 hours ALL69034 ..... 1310 to 1330
before installation. ALL69037 ..... 1310 to 1330*
ALL26950 .....Clutch Friction Discs 6-Pack ALL69035 ..... 1310 to 1350 Width = B, Caps = A
ALL26952 .....Steel Clutches 5-Pack ALL69036 ..... 1330 to 1350
*Standard 1330 spread with larger 1.125" diameter caps.
www.allstarperformance.com 253