Page 153 - 2021-22_EngineCatalogAP
P. 153

ENGINE BLOCK SLEEVES
   Part No.
 Application
  Rough Bore
 Outside Diameter
Length
  Wall Thickness
 Flange Thickness
 Flange Diameter
    Darton Sleeves
   DAR300-022
LS7 Single Cylinder Replacement
  4.110"
 4.310"
5.800"
  0.100"
 .210"
 4.565"
  DAR300-023-DF
LS2/LS3/LS7 3.897" Undersized Bore
 3.875"
  4.325"
 5.800"
 0.225"
  .215"
  4.575"
  DAR300-023-SF
LS2/LS3/LS7 3.897" Undersized Bore
 3.875"
  4.325"
 5.800"
 0.225"
  .215"
  4.575"
  DAR300-024
LS1/LS6 Replacement 3.897" Bore
  3.890"
 4.180"
5.600"
  0.145"
 .285"
 4.320"
  DAR300-027-DF
LS7 Replacement Sleeve Dual Flat
 4.110"
  4.325"
 5.800"
 0.108"
  .215"
  4.575"
  DAR300-027-SF
LS7 Replacement Sleeve Single Flat
 4.110"
  4.325"
 5.800"
 0.108"
  .215"
  4.575"
        MAIN BEARING CAPS
   Billet Speedworks
Billet Main Bearing Caps
Billet main caps offer increased bottom end strength. Many of the billet caps listed are for converting a two-bolt main block to the more durable four-bolt main configuration.
 Part No.
 Description
  Caps
  Block
  Register
   PGESBLS1
Stock Block LS, 4.0L, 5.3L, LS1, LS2, LS6 (5 Cap Set)
  Stock
 Stock
 Stock Step
     CRANKSHAFTS
    LS-Based Forged Steel Crankshafts
Callies
Compstar LSx features Spec 4340 material, mid-weight design, multi heat-treated, double stress-relieved, nitride-hard- ened, properly placed counterweights profiled for piston clearance, drilled rod journals, precision ground and mirco-pol- ished to 5Ra. Dragonslayer LSx features Spec 4340 material, mid-weight design, multi heat-treated, double stress-relieved, nitride-hardened, properly prepped counterweights, gun-drilled mains, lightened rod journals, dual linear post keyways, pre- cision ground and micro-polished to 5Ra.
Dart
Features 4340 billet steel, 8 counterweights added front, center, and rear, heavy-duty rod cheeks, small hole through the rod pin, dual keyway provision, large radii for narrowed rod bearings, chamfered oil holes, highly polished journals, no Mallory required. 800-900 HP naturally aspirated, and works in power-adder engines. Recommended for use with LS Next/ SHP LS Blocks. Fully polished option special order only.
 Part No.
   Description
   Stroke
Min. Rod Length
  Rod Pin
 Main
Rear Main Seal
  Balance
Target Bobweight Grams
  Approx. Wt./Lbs.
 CALAPO317-CS24
 LS1 Compstar, 24-Tooth Reluctor
  4.000"
6.100"
  2.100"
 2.559"
1-Piece
  Int.
1785
  55
  CALAPO31T-DS
  LS1 DragonSlayer, 24-Tooth Reluctor
  4.000"
 6.100"
 2.100"
  2.559"
 1-Piece
 Int.
 1785
 48
     Part No.
 Description
  Stroke
Min. Rod Length
  Rod Pin
 Main
 Rear Main Seal
    Balance
  Target Bobweight Grams
  Approx. Wt./Lbs.
   DRT9-34640006125-8 †
 LS1/LS6 Short Snout, 24-Tooth Reluctor
  4.000"
6.125"
  2.100"
 2.559"
1-Piece
   Int.
 1780
   60
     † These Dart cranks are precision fitment in Dart LS Next and SHP LS blocks.
    2021-22 ENGINE BUILDER CATALOG 151
    LS / LT (GEN-5) SERIES
   151   152   153   154   155