Page 31 - 2018 DIGITAL BROCHURE

7/1/15 10:02 Page 2
Natcem 35 6pp A4 01_15 PHP:Layout 1

NATCEM 35

Method of useApplication Prepare surface, remove Stop any running water Cut a rebate around any
paint, coatings, renders with NATCEM Waterstop. pipe or cable and fill with
and plaster. (See separate leaflet) sealant to form flexible seal
Preparing the surface Mixing the water. NATCEM 35 is designed General Tanking around pipe or cable.
Do not use on frozen or over For optimum results, mix using to give a fluid mix but this only After mixing, apply the material as Prepare the walls and floor which are to be treated by removing all paint
heated substrates (Outside the conventional mixing machines. develops after sufficient mixing. quickly as possible after mixing and surface coatings. Cut a chase a minimum of 10mm deep by 10mm
range of 0°c-30°c). Prepare the Always place the water in the The mix will appear dry at first. using traditional tools. A 10mm wide at all internal angles of the wall to wall and wall to floor joints, then
surface in advance to provide mixer or mixing container and add Continue mixing until fluidity minimum thickness of the material fill with NATCEM 35 as the work proceeds. Form fixing points by cutting
an adequate key. On glazed the powder. Gradually add the develops. If greater fluidity is is always necessary. Do not apply out an area at least three times the diameter and one and a half the length
brickwork the joints should be NATCEM 35 to no more than 3.6 required, more water up to a total additional water to the surface of the fixing, filling with the NATCEM 35 as work proceeds but clearly
raked out and the surface bush litres of clean water per bag whilst of 4 litres may be used. Exceeding during finishing as this may cause marking the position. Well dampen the surface with water but ensuring no
hammered to form a key. The continuously mixing the material. If this ratio will lead to lower strength, surface cracking. Once setting standing water. Mix the NATCEM 35, well dampen the surface again with
surface to which the NATCEM one bag or less is to be used the longer setting time and the risk of has started DO NOT attempt to water, carry out the rendering of the walls using standard and accepted
35 is applied should be clean, NATCEM 35 can be mixed with a surface cracking appearing. In cold remix or to smooth the surface. techniques ensuring at all times a minimum thickness of 10mm. Protect
free from dust and thoroughly rose bud type paddle attached to weather the set can be accelerated This will cause the mechanical against direct sunlight or wind until the setting has completed. Once the
dampened. Where necessary an electric drill (900rpm, 1000w). using warm water, likewise in hot properties, in particular strength NATCEM 35 has set, allow at least 1 hour before applying any surface Form chase at wall to floor and all internal wall angles minimum 10mm x 10mm.
steel or aluminium mesh can Mix vigorously for at least 2 minutes weather cold water can be used to and adhesion to be lost. coatings or covering to the walls or to the floors.
be used. Ensure that a 10mm after adding all the mixture to slow down the set.
minimum thickness of material
is obtained. One bag More than one bag

Priming
There is no need to prime any
reinforcement, but if priming
is preferred, any conventional
system may be used.

Cut out for fixing point. Fill fixing points and
clearly mark.

Rose bud paddle in electric Place 3.6 litres of water into Add water to the mixer Gradually add the After adding all the NATCEM 35
drill 900rpm 1000w. a container. at a ratio of 3.6 litres per NATCEM 35 to the mixer. mix continuously for at least
bag of NATCEM 35. 2 minutes at medium speed.

Well dampen surface with Apply material to wall. Ensure at all times a 10mm
Add the Natcem 35 to water After the NATCEM 35 has water ensuring no standing minimum thickness.
mixing all the time. been added mix for at least water.
2 minutes.