Page 142 - MUD-catalog-2019_Neat

OP 142
Quick-Change Options
Center Bar Insert Molds

5.0 x 4.0
5.0 x 4.0
6.5 x 3.5
6.5 x 3.5
.437 .437
1 .437 Standard Solid: .437 Standard Laminated: Standard Solid: .437 .437 Standard Laminated: .437 1 .437
1
1 1
1
1 1
Ejector
Ejector
4.000 Ejector 4.000 Ejector 4.000 Ejector 4.000 Ejector 3.500 Ejector 3.500 Ejector
3.500
3.500
3.38
3.38
3.88 3.88 3.88 Half 3.88 Half 3.38 Half 3.38 Half
Half .750 | Center Bar Insert Molds Half Half Half
.437
.562
.562
.562
.562
.437 6.496
.562 .437 ± .001 .562 .437 ± .001 Offset .437 6.496 ± .001 Offset .437 ± .001 ± .001 Offset .437 6.496 ± .001 Offset .437 6.496 ± .001
.562
.562
± .001
Offset 4.996 Offset 4.996 Offset 4.996 6.956 Offset 4.996 6.956 6.956 6.956
5.456 5.456 .246 5.456 .246 5.456 .246 .246
.246 .246 .246 .230 .246 .230 .230 .230
.230 .230 .230 A2 .750 .230 A2 .750 A2 A2
A A .750 A A A A A A
MUD Quick-Change Options for Mold Frames & Inserts
Ø .375 Ø .375 Ø .375 Ø .375
Ø .375 Ø .375 Ø .375 Ø .375
B B B B
B B B .750 B .750
.750 .750 B2 B2
B2 B2
2 2 2 2
2 2 2 2
5.50
5.50
5.50
.360
.360
.360 4.00 3 .360 4.00 3 .360 .360 4.00 Central 3 3 .360 .360 4.00 5.50 3 3 .360 .360 Central 3 .360 .360 Central 3
Central
.360
.360 Central .360 Central 2.625 Ejection Central 2.625 Ejection Central 2.625 Ejection 2.625 Ejection
.360
2.625 Ejection 2.625 Ejection 2.625 Ejection 2.625 Ejection
Standard Solid Standard Laminated Standard Solid Standard Laminated
Construction Construction Construction Construction
ITEM NO. A B ITEM NO. A A2 B2 B ITEM NO. A B ITEM NO. A A2 B2 B
08/10SSB221 1.877 1.377 08/10SLB281 1.877 0.877 0.877 1.377 84/90SSB221 1.877 1.877 84/90SLB281 1.877 0.877 0.877 1.877
08/10SSB222 1.877 2.377 08/10SLB282 1.877 0.877 1.377 2.377 84/90SSB222 1.877 2.377 84/90SLB282 1.877 0.877 1.377 2.377
08/10SSB223 2.377 1.877 08/10SLB283 2.377 1.377 0.877 1.877 84/90SSB223 2.377 1.877 84/90SLB283 2.377 1.377 0.877 1.877
Standard Interchangeable Insert Molds
Ordering Information for Center Bar Insert Molds
1 Frame clamps at this end of insert mold and ejector plates4 • Item number (see tables above)
are flush with this end of insert.
2 Support post not supplied. Grind +.001 to +.002 higher than • Steel grades: 1020, 4130 prehard, P-20 prehard and H-13;
height of ejection. 420 stainless and other grades on request
3 Thicker plate optional (quotation on request).
• H-13 and other tool steel insert molds supplied .010 oversize
on outside dimension, .010 to .013 oversize on thickness,
and .025 to .035 undersize in pin and bushing holes for
machining after required heat treating
• “ A” & “B” dimensions supplied .004 to .007 oversize unless
otherwise specified
• “ A” and “B” dimensions for insert mold must match those of
the removable center bar
U.S. 800-626-6653 ■ www.dme.net

Canada 800-387-6600 ■ Mexico 52-442-713-5666