Page 16 - MUD-catalog-2019_Neat

UF 16
05/05 UF Quick-Change U-Style

UF 321 Frame & Companion Insert Molds

Frame Companion Interchangeable Insert Molds

1 Frame clamps at this end of insert mold and ejector plates are flush with this end of insert.
ITEM 2 Support post not supplied. Grind +.001 to +.002 higher than height of ejection (see page C 131).
NO.
3 Thicker plate optional.
05/05 UF 321
Standard Solid: Standard Laminated: T-Style Laminated:
NOTE: Use of spacers allows this frame to accept 3.25 x 3.75 3.25 x 3.75 4.0 x 4.7
MUD 3.25 x 3.15 insert molds (see page OP 146). .375 .375 .31 Ø 5/16
1 1 1 Dowel
UF 321 Frame Upper – Side View
3.62 Ejector 3.62 3.62 Ejector .375
"S" 3.750 Half 3.750 Ejector 3.750 Half
Ø 2.358 Half 4.700 1.26
Ø 1.0 SB2310-63-001
Ø .125
.375 ± .001 .375 ± .001
.45 .90 .500 3.248 .500 3.248 .375
.45 Offset 3.598 Offset 3.598 .500
UC 2520 .50 .50 Offset 2.75
4.000
MUD Quick-Change Mold Frames & Inserts for U-Style | 05/05 UF 321
.28 .184 .184
NOTE: Sprue bushing supplied flat with .125 small .175 .450 .175 .184 3.598 ± .001 .45
.175
diameter orifice standard. A A2 3.248
A A
UF 321 Frame Upper – Top View Ø .250 Ø .250 A2 Ø .250
1.388 1/4-20 THD (10)
.450 B B2
B B B2
1.388 .240 .240 .50 .240 .45
2
2 2.75 3 2
1.875 2.75 3 .240 Central 2.75 3
.240 Central .240 Central
1.865 1.865 1.865
Ejection Ejection Ejection
2.437 Standard Solid Construction
ITEM NO. A B
UF 321 Frame Lower – Side View 05/05 SSU 221 1.377 1.377
.190 .45 05/05 SSU 222 1.877 1.877

1/4-20 .190 2.76 Standard Laminated Construction
THD ± .0005 2.31
.125 1.865 ITEM NO. A A2 B2 B
* 05/05 SLU 281 1.377 0.877 0.877 1.377
.15 05/05 SLU 282 1.877 1.377 1.377 1.877
2.88 .45
Ø 1.001 T-Style Laminated Construction
* O degree - 15 minute taper slot to accommodate sleeve ITEM NO. A A2 B2 B
ejection retainer plate. Slot tapers from .125 to .109 in 05/05 TLU 201 1.450 1.000 1.000 1.450
3.750 length .
05/05 TLU 202 1.950 1.500 1.500 1.950
UF 321 Frame Lower – Top View
Ordering information for frame and companion insert
+.002
3.253 –.000 3/8 x 5° Lead molds can be found in the front of this section.

4.75
3.750
1.875 1.500

1.00
.375
4.88

U.S. 800-626-6653 n www.dme.net

Canada 800-387-6600 n Mexico 52-442-713-5666