Page 33 - Parker - Process filtration
P. 33
®
Fulfl o PCC Filter Cartridge
SPECIFICATIONS Performance Attributes
Materials of Construction Flow Rate and Pressure Drop Formulas
Phenolic impregnated cellulosic Flow Rate (gpm) = Clean ΔP x Length Factor
media (PCC) Viscosity x Flow Factor
Polypropylene support Clean ΔP = Flow Rate x Viscosity x Flow Factor
Stainless steel support (optional) Length Factor
PCG is glass-modifi ed cellulose
Beta Ratio (ß) =
Upstream Particle Count @ Specifi ed
Recommended Operating Conditions Particle Size and Larger
Maximum 10gpm per 10 in length
(38 lpm/254 mm) Downstream Particle Count @ Specifi ed
Stainless Steel Support: Particle Size and Larger
Maximum Temperature: 250°F (121°C) Percent Removal Effi ciency = ß-1 x 100
( )
Maximum DP: 50psi (3.5 kg/cm ) ß
2
Optimum Change Out DP: Performance determined per ASTM F-795-88. Single-Pass
2
35psi (2.5 km/cm ) Test using AC test dust in water at a fl ow rate of 3.5gpm per
10 in (13.2 lpm per 254 mm) cartridge.
Polypropylene Support Notes:
Maximum Temperature @ 10psid 1. Clean ΔP is psi differential at start.
2. Viscosity is centistokes. Use Conversion Tables for other units.
2
(0.7 km/cm ): 200°F (93°C) 3. Flow Factor is ΔP/GPM at 1cks for 10 in. (or single).
4. Length Factors convert fl ow or ΔP from 10 in. (single length)
Maximum Temperature @ 35psid to required cartridge length.
2
(2.5 km/cm ): 125°F (52°C)
PCC/PCG Flow Factor Liquid Particle Retention Ratings (μm)
Maximum P @ 75°F (24°C): (psid/gpm @ 1 cks) @ Removal Effi ciency of:
60psi (4.2 kg/cm )
2
Rating Flow Factor Cart. ß=5000 ß=1000 ß=100 ß=50 ß@2
2
Change Out DP: 35psi (2.5 km/cm ) (μm) Absolute 99.7% 99% 98% μm
2 0.026 PCG020 10 8.6 1.8 0.9 110
Filtration Ratings
99%+ at 2μm, 3μm, 10μm, 30μm, 3 0.017 PCC3 12 10 3.2 1.7 64
and 60μm pore sizes 10 0.002 PCC10 22 18 6 3.2 35
30 0.001 PCC30 100 85 11 4.5 25
60 0.0005 PCC 60 150 90 30 15.0 10
Ordering Information
— —
Cartridge Code Nominal Length Support Construction Seal Material End Cap Confi guration
PCG020 2 CODE INCHES (MM) CODE MATERIAL CODE MATERIAL CODE DESCRIPTION
PCC3 3 9 9 5 ⁄ 8 " (244) Poly Foam AR 020 O-ring/Recessed (Gelman)
A Polypropylene (DOE/SOE) P (DOE Gasket Only)
PCC10 10 10 9 13 ⁄ 16 " (249) DO Double open end (DOE)
PCC30 30 19 19 5 ⁄ 8 " (498) G 304 Stainless Steel (DOE) E EPR DX DOE w/Core Extender
N Buna-N
PCC60 60 20 19 15 ⁄ 16 " (506) 120/120 (Filterite LMO and
LL
S Silicone Nuclepore Polymeric Vessels)**
29 29 ¼" (743)
V Viton ® LR 120 O-ring/Recessed (Nuclepore)**
30 30 1 ⁄ 16 " (764)
Std. Open End/Polypro Spring
40 40 (1016) OB
Closed End
213 O-ring/Recessed (Ametek &
PR
Parker LT Polymeric Vessels)**
SC 226 O-ring/Flat
SF 226 O-ring/Fin
TC 222 O-ring/Flat
TF 222 O-ring/Fin
TX 222 O-ring/Flex Fin
Extended Core Open End/Polypro
XB
Spring Closed End
*Available only in 9 5 ⁄ 8 ˝ (-9) and 19 5 ⁄ 8 ˝ (-19) lengths
Specifi cations are subject to change without notifi cation. © 2010 Parker-Hannifi n Corporation
For User Responsibility Statement, see www.parker.com/safety domnick hunter Process Filtration - North America
All Rights Reserved
Fulfl o is a registered trademark of Parker-Hannifi n Corporation
Viton is a registered trademark of E.I. DuPont de Nemours & Co., Inc.
DS_IP_PCC Rev. A
33